frolic1 Posted November 11, 2009 Share Posted November 11, 2009 I just ordered a full length titanium mag tube and spring from Kip at Carriercomp. Judging from the number of posts on this I would expect that there are many on this board that have installed this mag tube from Kip. I just wondered how easy the installation was. Is it hard getting the old tube off? (I have a new M4). Is a heat gun required? Does the new tube come with complete installation instructions? Are any special tools needed? Quote Link to comment Share on other sites More sharing options...
bignotti Posted November 11, 2009 Share Posted November 11, 2009 Congratulations on your purchase! Instructions are included with your tube. Installation is straightforward. Quote Link to comment Share on other sites More sharing options...
Hookster Posted November 11, 2009 Share Posted November 11, 2009 I just ordered a full length titanium mag tube and spring from Kip at Carriercomp. Judging from the number of posts on this I would expect that there are many on this board that have installed this mag tube from Kip. I just wondered how easy the installation was. Is it hard getting the old tube off? (I have a new M4). Is a heat gun required? Does the new tube come with complete installation instructions? Are any special tools needed? Hi Frolic, Yes you'll need a heat gun. Mine took about 15 minutes of heat to release all the way but I was bringing the heat up slowly. Here's a copy of the instructions in this thread: http://www.benelliusa.com/forum/showthread.php?t=17726 Take Care, Hookster Quote Link to comment Share on other sites More sharing options...
Unobtanium Posted November 11, 2009 Share Posted November 11, 2009 FYI, Breakfree CLP has an almost identical "smoke point" to the adhesive's release point. When you start seeing CLP smoke, TWIST! Repeat until success is met. Just my last experience. Quote Link to comment Share on other sites More sharing options...
Hookster Posted November 11, 2009 Share Posted November 11, 2009 Yeah, mine released a little at a time. It was a kind of "heat/turn a little/heat/turn a little" process till it was about 1/3 of the way out a which point it unscrewed the rest of the way fairly easily. Hookster Quote Link to comment Share on other sites More sharing options...
LeoAtrox Posted November 11, 2009 Share Posted November 11, 2009 Yeah, mine released a little at a time. It was a kind of "heat/turn a little/heat/turn a little" process till it was about 1/3 of the way out a which point it unscrewed the rest of the way fairly easily. Hookster Same here ... And I really could have used a pipe wrench or something to get a better grip on the magazine. Leather-palmed gloves weren't cutting it; and my thin latex pot holders (kind of sticky, so I figured they'd grip well) were melting and falling apart. Quote Link to comment Share on other sites More sharing options...
BigHat Posted November 11, 2009 Share Posted November 11, 2009 (edited) I took a lot of baloney for mentioning it here, but I had purchased an inexpensive strap wrench for a plumping project about the same time and it came in quite handy. Kip commented that he has used one as well. NOT REQUIRED but it makes it go quickly if you have one kicking around. You'll need the heat gun for sure. Slip ring pliers are also required to remove/ replace the spring retainer properly. Edited November 11, 2009 by BigHat Quote Link to comment Share on other sites More sharing options...
Decodence Posted November 11, 2009 Share Posted November 11, 2009 Cooling the magazine tube with a damp rag also helps to get the tube out. I found that the tube was expanding too much when I removed mine. Quote Link to comment Share on other sites More sharing options...
OhioM4 Posted November 11, 2009 Share Posted November 11, 2009 I used a borrowed Craftsman Heat Gun. It was a nice one with a dial on the back to precisely adjust the heat output. I used a cheap pair of Sears welding gloves and had no problem unscrewing it by hand. Once it was up to temp it unscrewed slowly as the thread lock was thick and gooey. After it cooled the thread locker broke off really easy with a nylon brush. I did not need to use any solvent or acetone. Quote Link to comment Share on other sites More sharing options...
frolic1 Posted November 12, 2009 Author Share Posted November 12, 2009 Thanks for the comments, they were helpful Quote Link to comment Share on other sites More sharing options...
Unobtanium Posted November 12, 2009 Share Posted November 12, 2009 I have found bare hands work the best. Never tried the pipe wrench thing. All the of my M4's responded well to just hands and a heatgun. Quote Link to comment Share on other sites More sharing options...
taylaboy Posted November 13, 2009 Share Posted November 13, 2009 i followed Kip's directions and some of everyone elses. The strap wrench I got (Rubber) wouldnt bite, so I ended up putting it in a vice and using the rubber jar openers and oily rags which did the trick after applying the heat gun. You can get one for like $25 at home depot. Only advice I would give is if you use a vice, put wooden blocks on the receiver. Like an idiot I didnt and the teeth chewed off some of the cammo finish. Lesson learned. Kips tube is great, did he ever make the titanium charging handles? I know he was spec'ing it out, and was finishing up the rails. Quote Link to comment Share on other sites More sharing options...
garnok Posted December 2, 2009 Share Posted December 2, 2009 I second Unobanium. Bare hands and a heat gun work just fine. Comes off fairly easy when the area hits 250 degrees. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.