shotgunNoob Posted November 20, 2008 Share Posted November 20, 2008 (edited) Hey there- This question surfaced earlier, but I thought I would "renew" it. I have a SuperNova Tactical and noticed something weird going on with the interior finish of the chamber. There are 3 areas, all located where the barrel "slides" into the receiver chamber, that are missing the black coating found on the rest of the chamber interior. These areas are somewhat gold/silver in color and seem to be relatively symmetrical in their distribution. These areas extend roughly 2 1/2 to 3" into the chamber. When the barrel is installed you can hardly see them, if at all. Now, I contacted Benelli and they said that, upon looking at one of the shotguns they had, it is considered "normal" and would probably not be considered warranty worthy. They claimed that these areas were intentionally left bare for fitment purposes. Im somewhat dubious about this. Anyway, I have fired many rounds through this gun without issue and everything seems to work/fit properly. However, I am concerned about this exposed metal. I realize this is aluminum, but Im sure it can eventually begin to oxidize. I try to put a light coat of lubricant on these areas every 3 months or so. Still...this seems like an unneccessary problem. Any thoughts? Edited November 26, 2008 by shotgunNoob Quote Link to comment Share on other sites More sharing options...
cody6.0 Posted November 20, 2008 Share Posted November 20, 2008 I'll check mine out tonight and get back to you. Quote Link to comment Share on other sites More sharing options...
shotgunNoob Posted November 21, 2008 Author Share Posted November 21, 2008 I'll check mine out tonight and get back to you. Ok...thanks. Quote Link to comment Share on other sites More sharing options...
shotgunNoob Posted November 26, 2008 Author Share Posted November 26, 2008 (edited) Just took these photos to give you guys a better idea of what Im dealing with here. Again, Benelli considers this "normal" and not worthy of a warranty claim. Sorry about the image quality. I couldnt find my good camera, so the cell phone had to do. Either way, you get the idea. So, are these odd looking areas going to pose a problem or not? I understand that, due to the chamber/receiver being aluminum, rust isnt as big of an issue. However, better to be safe than sorry I suppose. Thoughts? Edited November 26, 2008 by shotgunNoob Quote Link to comment Share on other sites More sharing options...
cody6.0 Posted November 26, 2008 Share Posted November 26, 2008 I took a peek at mine and it is the same those patches are where the guns skeleton is exposed. I assume it is made that way so the barrel rests on a surface that doesn't wear like the polymer skin/overcoat. Basically the same way a polymer framed hand gun has metal inserts at major wear and high stress areas. Quote Link to comment Share on other sites More sharing options...
tlingitndn Posted November 26, 2008 Share Posted November 26, 2008 I took a look in mine and the same thing is happening too. I am not to worried about it though. This is the receiver and the barrel slips into it and the chamber is in the barrel not the receiver. I am assuming this is from the pressure and stress that shooting a shell causes. If it does bother you I would have gunsmith redo the finish or try spray coating that you can spray and bake on a new coating. Check out the link. www.sportsmansguide.com and use item number HX8A-96464 Quote Link to comment Share on other sites More sharing options...
cody6.0 Posted November 26, 2008 Share Posted November 26, 2008 Before you get to diehard take a peek inside a new one at a gun shop. Mine never had any plastic over the exposed skeleton part just the natural finish. There are a few places inside the reciever around the bolt that is the same way. Quote Link to comment Share on other sites More sharing options...
shotgunNoob Posted November 26, 2008 Author Share Posted November 26, 2008 Thanks for the replies. Now that I know this truly is "normal", I will probably just keep a decent coat of lubricant on these areas and forget about it. Thanks again!! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.