Jump to content
Search In
  • More options...
Find results that contain...
Find results in...
Benelli Forums
SFBayArea

Do you have GG&G Tactical Bolt Release Pad?

Recommended Posts

Anybody has a write up on how to install it?

 

If you have it installed, how long ago you installed it? Does it leave marks on the gun? I've read some old posts that it does scratch surface of the gun after some use. I was wondering if GGG changed anything in their design to fix the scratching issue.

 

I have the pad in my hands, but I am debating if I want to install it or not. It seems that installation is not really easy. I don't want to screw up my new gun with bad installation or make visible scratches from use in the near future.

 

Thank you.

Share this post


Link to post
Share on other sites

I'm not a fan. It's a bit large, and I like round buttons. Less snag. Less chance of an impact causing the button to rotate (the way the button is attached in the shell-release allows it to rotate if enough force is applied. A non-circular shape can easily cause this if struck, etc. WIth the round release button, rotation could theoretically still occur, but would be meaningless. I have sawn the assembly in half, and this rotation, SHOULD it occur, is NOT indicative of a pending or even remotely possible failure. Having your release button hit your charging handle could be...(I have not measured to see if this is possible, but it looks like it might be with GG&G).

Share this post


Link to post
Share on other sites

Well Uno, since no one makes a round button like you've fabricated for yours perhaps you could make some like yours and sell 'em. I'd buy a couple.

Share this post


Link to post
Share on other sites
Well Uno, since no one makes a round button like you've fabricated for yours perhaps you could make some like yours and sell 'em. I'd buy a couple.

 

Well, nothing fancy, there. I'd love to rip you off, but I'm too nice for that. Here's the magic formula...

 

http://www.tac2.com/index.php?template=bbr

 

Tell them just to send the threaded shell-stop, don't worry about the button. The shell-stop is 4-40 threaded and otherwise a factory/OEM part. I had a machine-ship (5 axis CNC equipped...not a cheap place) thread an OEM bolt release for me once, and Tac2's job looked better.

 

Then...

 

any 4-40 threaded 1911 magazine release button will work. SVI, Shooter's connection, etc.

http://www.sviguns.com/1101.php?indx=10

Near the bottom of hte page is the one I am using in my next build. I got the "blued" one, but it doesn't seem to be bluing. I soaked it in vinegar for 30 minutes and it didn't change color or anything. It's not likely parkerizing unless they parkerized it very lightly or something, but I like it. It matches things. Button top is slick, which I kindof like. You are depressing it, not sliding it. Texture is not needed, and may even hamper things if you just like to slap at it like some people do.

Edited by Unobtanium

Share this post


Link to post
Share on other sites

Here you go, this is the "Thin blued large" button from the link above, installed (the pix on their site are terrible):

 

e0fuv9.jpg

*Picture taken using flash

 

(that button sat in white vinegar for 30 minutes...no clue what they use, but I buffed it with a paper-towel, and all that, including the vinegar, and got nothing off of it. Also used acetone. Whatever it is is decent enough!)

There you are, for about $80-90 shipped...

Share this post


Link to post
Share on other sites

My solution is, in my mind, more attractive, won't harm the finish of the weapon, has less movable parts (button is monolithic and includes its own "screw"), is less prone to failure (You need to use blue loctite, here.), and will work very well. It's also significantly cheaper.

Share this post


Link to post
Share on other sites

Do any of these solutions make installations easier? Without disassembly of the whole release button?

Looks like I will be sending GG&G button back.

Share this post


Link to post
Share on other sites

PM Benelliwerkes or StrangerDanger, and check with them. These guy's are great contributors. I installed one of these myself. The key is to have the right roll pin punch, patience, and make sure the roll pin is positioned correctly.

Share this post


Link to post
Share on other sites

I used SD's instructions perfectly. Cheap trip to Harbor Freight for punches/holders/clamps/etc and a craft store for a bit of sticky felt backing on the pad and good to go

Share this post


Link to post
Share on other sites

Addendum: svi emailed me back and told me that the button is 416 Stainless with a black oxide stainless bluing process. Completely overbuilt for this application. Perfect.

Share this post


Link to post
Share on other sites
Do any of these solutions make installations easier? Without disassembly of the whole release button?

 

No. Any of those solutions require removal of the OEM part. Unless you are going to try and drill & tap the OEM button while it's still in the gun. Not a good idea. Actually, a very BAD idea. You're either going to have to replace the OEM with a ready-made piece that's already been d&t'd (GGG, TAC2), OR you're going to have to take the OEM part out, d&t the button for whatever larger button you're going to install, then put it back in (Nordic, Taran, Briley, etc). Removal and replacement of the part is simple with the right tools.

I've had the GGG part on two of my older guns for a number of years. One gets a lot of use in 3-gun. Never had an issue. No loosening. No marring of the receiver, although it's a tool and I don't give a rat's patootie about dings, scratches, and the like. Lately, I've put the Nordic round button on my newer guns. I think I like that one a little better.

Edited by truckcop

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...