JPN800 Posted March 12, 2006 Share Posted March 12, 2006 I recently bought a SBE II for duck hunting, And i like it for that. I took it out today to the local skeet range and put in the ***** choke (skeet) and couldn't hit anything . I feel that it is shooting too tight of a pattern. I then picked up my Franchi and was doing fine. Which leads me to belive i need a different choke or something. Please give any insight to help me out. [ 03-12-2006, 01:56 PM: Message edited by: JPN800 ] Quote Link to comment Share on other sites More sharing options...
Frenchie Posted March 12, 2006 Share Posted March 12, 2006 I am going to be buying a new shotgun in the next couple of weeks, and could use some advice. I am looking at the SBE II and love the way it feels, but am concerned about what I have read about it not cycling light loads consistently. I have read that the M2 handles the lighter loads better. I want this to be the last shotgun I purchase, so I want to purchase wisely. I will use the gun for shooting clays, turkey hunting, and possibly some duck hunting. I may want to buy a slug barrel eventually as well. Any recommendations from owners would be appreciated. Quote Link to comment Share on other sites More sharing options...
mudhen Posted March 12, 2006 Share Posted March 12, 2006 Doubtful the SBE II is too tight with the skeet choke. Much more likey the POI does not match the POA. I have to fudge with my drop spacers all the time on my SBE II. It shoots 70/30 with the A, 60/40 with the B, 50/50 with the C, and 45/55 with my homemade D (best for me for ducks). My Browning BPS shoots 50/50 all the time. No spacers to adjust, so I guess I got lucky. Go pattern it and see if it hits where you are aiming. Make adjustments from there. You can also look into the higher cheek pad if that helps you. mudhen - CA Quote Link to comment Share on other sites More sharing options...
IdahoDucker Posted March 13, 2006 Share Posted March 13, 2006 Hey Frenchie, The SBEII is not designed to shoot "light" loads. Benelli specifically recommends nothing less than 3 dram, 1 1/8 oz loads. It's an inertia driven shotgun. Meaning it has to have sufficient recoil to cycle. Light loads, especially in a new gun, may not cycle. Some guns will cycle 1 oz. loads after a sufficient break in period but don't count on it. It's a hunting gun so expect it to perform accordingly. With normal hunting loads you should never have a problem. Quote Link to comment Share on other sites More sharing options...
sasha1474 Posted March 13, 2006 Share Posted March 13, 2006 Frenchie- I have a new M2. I have put around 100 rounds through it and the last 50 were 1 oz. loads at the trap range. Not one hiccup. Gun functioned flawlessly! Quote Link to comment Share on other sites More sharing options...
JPN800 Posted March 14, 2006 Author Share Posted March 14, 2006 Originally posted by mudhen: Doubtful the SBE II is too tight with the skeet choke. Much more likey the POI does not match the POA. I have to fudge with my drop spacers all the time on my SBE II. It shoots 70/30 with the A, 60/40 with the B, 50/50 with the C, and 45/55 with my homemade D (best for me for ducks). My Browning BPS shoots 50/50 all the time. No spacers to adjust, so I guess I got lucky. Go pattern it and see if it hits where you are aiming. Make adjustments from there. You can also look into the higher cheek pad if that helps you. mudhen - CA Thanks i just installed the c shim and i "think" the sights line up better for me, I didn't even know what those were for . What do you mean by 70/30 or 50/50. sorry for the dumb question. Hopefully i will try it again on sunday. Quote Link to comment Share on other sites More sharing options...
mudhen Posted March 14, 2006 Share Posted March 14, 2006 % of how much of the pattern hits above or below a given aim point. mudhen - CA Quote Link to comment Share on other sites More sharing options...
Paolo Posted March 14, 2006 Share Posted March 14, 2006 How hard is it to change the shims on a SBEII? I'm always concerned about doing something wrong when taking it apart. Paul Quote Link to comment Share on other sites More sharing options...
tucker301 Posted March 14, 2006 Share Posted March 14, 2006 Paolo, carefully take note of how the shims are marked and oriented when you disassemble, then refer to the guide in the manual. Once you see it, the manual will make sense to you. Quote Link to comment Share on other sites More sharing options...
mudhen Posted March 14, 2006 Share Posted March 14, 2006 Takes me about 30-45 seconds. mudhen - CA Quote Link to comment Share on other sites More sharing options...
tucker301 Posted March 14, 2006 Share Posted March 14, 2006 Are we still talking shims? Quote Link to comment Share on other sites More sharing options...
Frenchie Posted March 15, 2006 Share Posted March 15, 2006 Originally posted by sasha1474: Frenchie- I have a new M2. I have put around 100 rounds through it and the last 50 were 1 oz. loads at the trap range. Not one hiccup. Gun functioned flawlessly! Quote Link to comment Share on other sites More sharing options...
Frenchie Posted March 15, 2006 Share Posted March 15, 2006 I just picked up my new M2 today and it looks great. I cleaned it up and am all ready to shoot this weekend. What type of shells did you shoot through yours when breaking in? I typically shoot an O/U Lanber with the cheap Wal-Mart Federals, but am willing to step in up for my new investment. The manual recommends standard "field loads", but that could mean 3" or 2-3/4". I want to break it in right from the beginning. Please let me know. I can't wait to squeeze a few off, the gun is awesome, and I think I got a fair deal at $977. Quote Link to comment Share on other sites More sharing options...
JPN800 Posted March 20, 2006 Author Share Posted March 20, 2006 I went out shooting yesterday and it feels like a different gun now, With the "C" shim installed. I was very disappointed last week but i feel like i made the correct choice now. Quote Link to comment Share on other sites More sharing options...
IdahoDucker Posted March 21, 2006 Share Posted March 21, 2006 Frenchie, Break in loads would be anything you might use for ducks or pheasants. 2 3/4 or 3" doesn't matter. Find something in 1 1/4 ounces of shot or more and it'll do the job. Of course now the weekend is over so maybe you already did it. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.