Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12

Thread: Removal of M4 magazine tube

  1. #1
    Join Date
    Jan 2009
    Posts
    3

    Default Removal of M4 magazine tube

    Just ordered a 7 round magazine tube to replace the factory 5 round tube for my M4 Benelli. Any tips on how to easily remove the fac. tube in order to install the new titanium desert tan one?

  2. #2
    cleefurd Guest

    Default

    Quote Originally Posted by mgdoc8307 View Post
    Just ordered a 7 round magazine tube to replace the factory 5 round tube for my M4 Benelli. Any tips on how to easily remove the fac. tube in order to install the new titanium desert tan one?
    Hi mgdoc8307,
    This is "cut-n-paste" from our Gunbroker.com listing, in case you ordered from our online store where directions have not yet been uploaded. Sorry to leave you hanging. Hope this helps;


    Tools required;
    > Heat gun.(Refrain from using flame devices, torches, etc., they are overkill and have the potential of discoloring the finish on the receiver)
    > Snap ring pliers.
    >Stiff nylon or brass bristled tooth-brush, Q-tips and acetone.
    > Rubber grip pad. (Similar to a jar lid gripper, or even a piece of tire inner tube)
    >Padded vise. (not required but helpful if done alone without an assistant)

    Before proceeding please ensure the firearm is completely unloaded, clear mag tube and chamber, firearm on safe.

    Lock the bolt to the rear, then remove the factory barrel nut (by hand), set the barrel, bolt group, and handguards to the side. Using snap ring pliers set to compress when gripped, carefully remove the spring retainer from the end of the factory mag tube, (keep it aimed away from your face, with your other hand over the end so that the spring can be safely contained when it is "set free"). Then tilt the gun downwards, allowing the spring and follower to fall out. Place gun in a lightly clamped padded vise (ensuring the bolt release button is not clamped), between your knees, or in the hands of a competent assistant. Using the heat gun set to a maximum 400 F, apply direct heat to the full circumference of the mag tube where it meets the receiver, allowing heat to reach the receiver as well, continue rotating the heat around the junction until the two are beyond unbearable to touch (using an infra-red thermometer if available, you will typically see results when the receiver temp nears 250F), favor application of heat to the receiver, as it retains heat more efficiently. At that temp (around 250F) you should be able to begin twisting the factory tube off [ccw](here's where the rubber grip pad does double duty as a heat shield, and provides much better grip than bare hands). Do not use a pipe wrench for a few reasons, 1st it will damage your factory tube, but foremost it will provide excessive torque that may allow you to force removal before the loc-tite is ready to let go. Once it starts to turn, the battle is won, just keep it turning until it is free. Next clean the internal threads with acetone, Q-tips, and the nylon or brass tooth brush. It will look scary at 1st since the residue from the factory loc-tite is chalky white, but once you have it all cleaned off, you should be looking at the pristine black anodized receiver threads where the old tube use to be. You are now ready to install your replacement tube. Don't forget to transfer the handguard's stamped steel rear brace onto the new tube BEFORE threading it into the receiver, it is a "captured part" that has to be in place during assembly. Most people opt to fore-go the use of loc-tite, simply torqing in their new tube as tight as can be done by hand. If you use loc-tite, make sure you check the data sheet, and select a grade that can be heated for removal with LOW HEAT like the factory used. Typically just a drop of medium strength Loc-Tite brand "blue" will be sufficient if you use any at all. Replace all the remaining components, and enjoy!!

  3. #3
    Join Date
    Jan 2009
    Posts
    3

    Default Removal of Mag. tube from M4

    Will a hairdryer work as a "heat gun"? Thanks, Michael

  4. #4
    Join Date
    Apr 2009
    Location
    Pennsylvania
    Posts
    2

    Default

    cleefurd,

    Thanks for the instructions. Worked like a charm.
    New titanium tube from Carriercomp is installed and a beautiful thing.

  5. #5
    Join Date
    Nov 2009
    Posts
    25

    Default

    +1 on the hair dryer. Would save me the trouble of borrowing one.

  6. #6
    Join Date
    Apr 2009
    Location
    Illinois
    Posts
    316

    Default

    Going to need a really REALLY hot hairdryer ...

  7. #7
    Join Date
    Nov 2009
    Posts
    25

    Default

    Quote Originally Posted by LeoAtrox View Post
    Going to need a really REALLY hot hairdryer ...
    Roger. When you gents replaced your tube, what kind of loc tite did you use? My buddy has most of the tools and was wondering if I should pick up some blue? or red? I forget which one is ok on weapons.

  8. #8
    cleefurd Guest

    Default

    Blue (medium strength) if any at all. It is not necessary as long as you use both hands with a good grunt when you seat the replacement tube.

  9. #9
    Join Date
    Dec 2009
    Posts
    16

    Smile good write up

    thanks for the write up ..got save this one ..placed order on ext barrel ..now just got to wait the 4 to 6 week time..good help..

  10. #10
    greeder7 Guest

    Default

    Interesting post dude....Forums are always helpful in one way or the other. Thanks for giving out information. Itís really nice and mean full.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •