Intervention
-
Posts
64 -
Joined
-
Last visited
Posts posted by Intervention
-
-
-
The MB get's me into the 20" minimum barrel length trap range here in LA until the 6" barrel extension shows up then I can get into the 24" minimum range!
-
Just finished my Benelli M4 build today.
Before 7.8 lbs
After 8.2 lbs
with Brake 8.10 lbs
922r compliantReceiver with 7 foreign parts and 6 US parts.
Barrel
Bolt
Bolt carrier
Gas piston
Butt stock
Pistol Grip
Forearm/hand guard (forend)
Benelli 7+1 Magazine body – Carrier Comp - USA
Trigger housing – A&S Engineering - USA
Trigger – FFT - USA
Hammer – FFT - USA
Disconnector –FFT - USA
Follower – Carrier Comp - USA
California compliant Pinned Benelli Telescoping Stock.
Zeroed to 50 yards - Amazing shooter. Ordering a Briley 6" barrel extension, choke and I have a Benelii Standard Non-Pistol Grip stock so I can shoot at the stuffy trap ranges here in LA!
-
The Limbsaver is a model 10111. It isn’t a direct fit. You’ll need a Noveske adapter plate. To make the collapsible stock functional in the fully collapsed position, you’ll need to modify the pad and the adapter plate. You’ll need to drill a hole in to the buttpad where the receiver extension passes through the stock and into the pad. If I recall it’s like a 3/4” or 7/8” hole. The adapter plate needs a section cut out of it to permit the receiver extension to pass through as well. I just hacksaw the section out and shape the pieces on the grinder. Each piece is held in place by one screw. When you screw the stock in to place, it bridges the parts and keeps them solidly together.
Youll need to source some 8mm long screws for the Noveske adapter. I get them from my local hardware store. The screws supplied will fit for the buttpad to screw in to the adapter plates.
You can can count on a realistic reduction in perceived recoil of about 40%. Harder the load, the better it performs. No issues with lighter loads either.
You may may be right about the Taps switch. It is rather big and thick. I don’t have an issue with where the buttons would be. The momentary button would be beneath my thumb, and the secondary button would be set to a constant on toggle within reach of my thumb. The issue is attaching it in a functional manner. You can’t cut the handguard too deep since the piston housing is there.
Mid I can get by without using their bottom plate, my job will be much easier. If mounting to that Strike rail, the mLOK would fit well. I’m just not sure if I can tolerate all that cheese grater machining.
Thank you for the information on the Limbsaver. Do you have pictures of how the Limbsaver looks mounted with the Noveske adapter?
Has anyone used a Limbsaver Grind to fit on the M4 Telescoping stock? I read somewhere that you could use a grind to fit and drill out the middle and the stock would collapse all the way and look like a stock part?
-
Thank you for the color match
-
Does anyone know what paint color will closely match the Benelli M4 standard barrel color?
I am installing a Briley Barrel extension and would like to paint it to match the barrel.
-
Could you provide information on the limb saver for the telescopic stock?
-
Thank you! Either one works out here in Cali just fine!
I think the button is the same stuff they made Iron Man out of
-
Nice work Rasyad,
I just did almost the same thing, drilled and taped a hole a 6-32 hole in the stock release button (This is one hard piece of steel).
Reassembled the stock release button and spring positioned the stock to the length I wanted
I cut an old drill bit approx 1/2" in length and dropped it in the hole.
Installed a 6-32 x 3/8" set screw and tightened it down.
-
I want two please
-
What color is that A&S, grayish?
-
I went with the T-2, better for shooting slugs out to 100 yards for me.
My Benelli M4 build
in Benelli
Posted
5.1 ounces
Stock Setup 297.97 g
Steel Tube 292.08 g
Ti Tube 152.68 g
The weight difference between the stock setup and ti tube is 145.29 grams = about 5.1 oz