kmc0929
-
Posts
112 -
Joined
-
Last visited
Posts posted by kmc0929
-
-
I asked this before but have yet to get an answer, has anyone been able to get an actual specific size wrench for the front sight nut on an M4 shotgun? I can't get a hold of anyone at Benelli that seems to know this...
Looking for an exact size wrench, I am sure one exists, how would they put them on at the factory...
-
so why havent more people done this?
like I said I really dont want a change out the handguards, I think mounting a rail to the stock ones wouldnt be that bad. will it really be that bubba? i however was planning to mount it to the flat spot closer towards the barrel. anyone else done this?
-
**** i paid 900 for mine, and i hate railed forends, i just want a little spot with A rail on it.
in fact i buy surefire direct and i still dont really want one.
-
Anyone ever tried to bolt a small rail onto the flat part, about 3:00 on the stock M4 handguards. I was thinking about bolting a small rail onto the right handguard, theres about a 3/4" flat spot I think it would fit. Im sure someones already tried this.
Second question, in case I muff this up, where can I get some replacement stock m4 handguards.
-
the one i saw, i want to say was on a supernova or something like that, and didnt have a rail system other than the top rail
-
Anyone seen one? I saw a picture of something that looked like one, maybe it was on a m2, I don't remember where, it was like a M3 mounted 3:00 on the receiver.
-
ok fine ill leave it be, but one last question
does the nut go on, flat side up, or rounded side up.
the nut has a rounded side, with some clear stuff inside of it, i couldnt get that side to go on first so i went flat side first.
excuse me, now i know what a nylock nut is, so does the nylon part go first or the plain part
-
i just wish there was a clear answer to this. i have the new nut tightened on there but its not very tight. i want to tighten it down but 5.5 is going to round it off.
what is the actual size, i wish i had some calipers.
-
benelli usa just told me on the phone it was a 3mm wrench...
-
Anyone seen a different wrench other than the set at sears? the sears set is so thin i think that helps it round off the nut. a thicker wrench would be better.
-
Thanks, now here is the hard part I have to take the rounded one off, not to mention i put a dab of red loctite on there... i know....
i guess i will just heat it up and try to use that same 5.5 ignition wrench again. ANY ideas on a better wrench?
-
I chewed the **** out of the nut that holds the front sight blade on there when replacing it. I think I was using a 5mm or 5.5mm ignition wrench. Is there anywhere I can find a better wrench and a replacement nut?
-
I wont use it very much, so any thoughts on the specter line? or the wilderness line?
-
hows that transition?
-
What seems to be the standard in a two or three point sling for the M4? Something that will utilize the factory attachments and wont roll over on the user.
-
how do you remove that tube? heat?
-
anyone have a picture of a notched one and an unnotched one?
-
Ok, what I think I actually need to know is, how can I tell if I have the multiple position buffer tube, and what will happen if i put a coll stock on a non coll tube.
-
So a friend from Beretta/Benelli said they could get me a collapsable stock. How can I tell if my m4 will accept one? Is there a part that goes over the recoil tube and has the notches or does my tube have notches on it? Let me know!
-
poppa beretta gave beretta to one kid, benelli to another, i think beretta handles all the LE stuff, and benelli does all commercial. that said beretta does benellis le stuff.
-
ok good, so there is a possibility that the barrel wont match the receiver, great, thanks for all the help.
-
??? Confused.
-
Benelli M4
1) Is the serial on both the barrel and the receiver? I think my gun is a Frankenstein, not that it matters.
2) Is the front sling attachment point supposed to be a little loose?
3) When assembled should the gas pistons move around a little? When I shake it around I can hear something loose moving around. The carrier moves well and all seems to function well.
-
so for a full length tube is mine too short then?
M4 Sight Nut
in Benelli
Posted
well thats what I used. is it really a very low torque type thing, because mine stripped at about hand tight. the fit of that wrench just seems a little off. almost like it needs to a be a 5.25mm wrench.