briarbeavis01

Thanks benelliwerkes for the pictures and advise. I believe I can handle my trigger group with all the help from you and StrangerDanger. I ordered my snap ring pliers today. I didn't see any I wanted at the local places to buy tools. StrangerDanger the H20 trigger pack looks great. But why not the trigger/disconnector/hammer sears? Thanks again for the help to you both!

Hello truckcop, found all the previous post. Thanks for the advise.

Hello truckcop, I have tried several different ammo brands and none I have will allow me to load seven. The Wolff spring extends a good bit in front of the tube. I don't really know where to start looking for other post on the subject. But thanks for letting me know there are post to search for. I'll try to search for Wolff springs. I think that is most likely the problem. Thanks again.

Just installed my Carriercomp mag tube with their new spring and a GG&G follower. I can only load six 2 3/4 shells of any kind in the tube. I haven't tried Carriercomp's follower yet. Has anyone had this problem or have I done something wrong? Thanks in advance.

I just finished readng your pictorial on the trigger group disconnector swap. Is the disconnector pin just hard to get started or easy to lose or both? I have some nice tools for the job. I may not have the patience for the job though. Thanks for all your help. It's really appreciated by us all here on the forum.

Just a thank you StrangerDanger for the mag tube pictorial. Just got my Carriercomp mag tube installed. Took less than ten minutes to heat and remove the factory tube. There was very little red loctite on the mag tube. Just have to install the new Geissele hammer and the FFT disconnector. Then I'm 922R compliant. I'm using a GG&G stainless follower. Does not have US on it that I can see but the company says it's US made. Wonder if that is a problem? Do have a factory collapsible stock installed. Thanks again for the help.

Thanks for explaining cerakote SD. I was thinking about Robar Poly-T2 gunmetal grey. Talked with a fellow at Robar and he said it was almost a black color. Never seen a picture of a long gun with that finish. Internals would be NP3. This is expensive though. He also suggested Roguard for a nice black finish.

They look great to me. How does the Cerakote hold up. As good as Robar's finishes or better?

Thanks StrangerDanger and AVATactical for your answers.

Can anyone tell me if this accessory (IWC Magpul MOE QD Sling Mount) fits the Benelli M4 collapsible stock without modification to the stock itself? Thanks in advance for any answer.

Thanks for the information. I was a little worried.

The top of the ejection port towards the rear of the port looks and feels rough like the shell casing is hitting the top of the port when the hulls are ejected. Is this a problem at all? Just feels kinda like a serrated edge but does not effect function of the firearm. Any ideas?

Thanks for the heads up. Ordered one last night. You used to could order by phone, but now you have to purchase online.

Benelliwerkes that photo says all no matter whether the Benelli or the M-16. I agree with a real deterrent to go viral. You'd think video's of beheading's would be enough to make some folk's see the light in this country.

M4DC you are right about FB. They don't make you take anything down, they just remove the post for you.

Hello benelliwerkes. Would you mind if I reposted this picture on facebook? Sure is funny!!!!!!!!!!!!

Thanks for your advise. I will start over. You're welcome for my comment on your mount. It's first class.

Hello. This is my first post and I have a question. I purchased the AVA mount and it is super. I installed the mount and only snugged the screws down just to see the mount on my M4. My question is, can I remove one screw at the time to apply the loctite primer and loctite or do I need to remove the mount and start over? I have not torqued the screws down with an inch pound wrench. If this is the wrong thread my apologies. My light is a Surefire E1D Defender with the Z61 on off switch. Thanks for any answer.