jetflyer

Thanks for the revision note. Try the link above again.

Thanks...try the link above again.

How about the real factory item? Factory Original +2 Extension [ 09-08-2006, 06:48 AM: Message edited by: jetflyer ]

this is currently for sale on ebay. its the real deal, brand new, factory sealed Benelli M4 +2 mag tube ext. 81043P. Benelli +2 Extension [ 09-08-2006, 06:44 AM: Message edited by: jetflyer ]

MODIFIED

skeletonized stock cheek pad?

I wish I could! That looks awesome. But our 3-gun match rules do not allow compensators or porting of the barrel. [ 02-26-2006, 04:07 AM: Message edited by: jetflyer ]

[ 02-27-2006, 08:15 AM: Message edited by: jetflyer ]

Sorry to sound negative. I went too far down the "conversion" road untill it became my obsession, instead of enjoying the gun itself. Benelli and the ATF restricted the civilian M1014 too much for me. I should have done more homework before I purchased the M1014 Limited Edition model. The M1014 can also be a very positive experience. And fans there are many. I mearly stated the obstacles for the conversion. Perhaps the knowlegde that I am passing along will spare another buyer like me, the disappointment. To end on a positive note...I am elated with my purchase of the M4/Law Enforcement model!!!! It is the gun, with all the full features that I wanted all along. Due to the difficulty of acquiring an M4 with all the "evils" included, I consider it my crown jewel. [ 02-27-2006, 08:14 AM: Message edited by: jetflyer ]

As a previous owner of an M1014, I will relate to you what I encountered... Regrettably, you cannot remove the M1014 recoil tube and replace it with an M4 tube. The M4 tube cannot be purchased as a spare part (to prevent us from converting the M1014 to a collapsible stock weapon). The M1014 recoil tube is "permanently" welded to the receiver with a powdered European version of a "Locktite" compound. Removal of the "welded" tube requires a heat and torque application that will damage the attached aluminum receiver. There is a gunsmith in Florida that will mill your M1014 tube without its removal. However, the dark finish that is on the tube will be ground off. The tube is stainless steel, and Benelli uses a proprietary chemical process that reacts with stainless to give it the dark mil-spec finish. It is NOT Parkerizing, as you might think. Parkerizing does not react with stainless. And the "polyresin" baked finishes wear off at the places of sliding contact. Some NFA rules were not lifted for imported weapons, and the BATF is very sensitive to THIS gun in particular. Benelli took note, and went to great lengths to defeat our attempts to convert the civilian M1014. My desire to own a legal and functioning collapsible stock became an obsession. So, I abandoned my conversion efforts and purchased a true M4. [ 02-25-2006, 10:45 PM: Message edited by: jetflyer ]

Who makes the front sight on the M4? (its not LPA) I am replacing the factory rear ghost ring with an LPA fiber dot ghost ring. I assumed that the factory front sight was made by LPA too. WRONG. The North American LPA distributor told me that only the rear are LPA, and he did not know who makes the front end of the Benelli ghost ring sighting system. Does anyone here know? [ 02-22-2006, 08:10 PM: Message edited by: jetflyer ]

How - specifically - do you get the one on the lifter. I have been trying but I guess I don't have the right info yet ... Thanks! Load up 7 in the mag tube, with the bolt CLOSED. Then retract the bolt rearward just enough to drop one on the lifter, and finally one in the chamber. Let the bolt slide shut. The key is to retract the bolt rearward enough to place the shells on the lifter and in the chamber, without reaching the bolt's rear locking position. It's difficult to do with a shot timer running or in competition reloading situation. It is a nice technique to master when you are told to "load and make ready"!

How - specifically - do you get the one on the lifter. I have been trying but I guess I don't have the right info yet ... Thanks! Load up 7 in the mag tube, with the bolt CLOSED. Then retract the bolt rearward just enough to drop one on the lifter, and finally one in the chamber. Let the bolt slide shut. The key is to retract the bolt rearward enough to place the shells on the lifter and in the chamber, without reaching the bolt's rear locking position. It's difficult to do with a shot timer running or in competition reloading situation. It is a nice technique to master when you are told to "load and make ready"!

Mine can hold NINE 2.75inch shells. Never malfunctions. 7 in the mag tube 1 on the lifter 1 in the chamber [ 02-03-2006, 09:55 PM: Message edited by: jetflyer ]

Trijicon ACOG 4x32 Scope with Yellow Center Illumination for M4A1 Model# TA01NSN [ 02-03-2006, 11:03 AM: Message edited by: jetflyer ]

This is a picture of my new M4 meeting his other brothers. Is it abusive to keep these boys locked up at times? [ 02-03-2006, 09:39 AM: Message edited by: jetflyer ]

I contacted the renouned gunsmith and trigger expert Allen Timney, to discuss any possible improvements or tuning services for the M4 Super 90 trigger. He said that little or NOTHING could be done to the stock trigger, nor did he care for it. I applaud him for his honesty, and for turning away an easy sale. Perhaps some military grade weapons should be left alone. [ 01-18-2006, 04:32 AM: Message edited by: jetflyer ]

Hey, thats my "ex" posing for pictures!!!!! I always suspected that she would be just as happy being held by another man. M1014, please don't tell me that your keeping her locked up too? [ 01-18-2006, 04:19 AM: Message edited by: jetflyer ]

M1014 is the resident guru...so with due respect to him, I'll try to answer the question untill he chimes in, as I own both the 11701 and 11707. The Benelli 11701 Limited Edition M4/M1014 has a fixed skeletonized stock(due to the recoil tube NOT machined for the stock to slide closed). The receiver has an engraved American flag to denote the limited edition version. And the barrel is the same as the military version, heavy(not the thinner walled "low recoil" problem child) and has a fixed choke(modified). The 11707 has the recoil tube is machined to allow the stock to collapse. No flag, but "m4" is engraved on the receiver instead. And the barrel has screw the screw in choke option. Early units shipped with the "low recoil" problematic barrel. Recent shipments are going out with the heavy, screw in choke version. Both have the screw off civilian mag tube fake extention that limits the tube to 5. Did I miss anything, M1014? [ 01-12-2006, 09:49 PM: Message edited by: jetflyer ]

gunbroker.com had a few ranging from $200-350, with days to go! cal's armory was selling them last month(before the benelli ban announcement) for $70! good luck

sold pending funds. thanks m1014.

FOR SALE This is a factory new stock for the M4/1014. It was taken off of a model 11707 to make room for the skeletonized version, and still has the peel off sticker. $75, Free Shipping. [ 01-10-2006, 08:02 PM: Message edited by: jetflyer ]

almost a year.

the ports are inside the barrel, closer to the chamber end and above the piston rods. ps...i am in marion often, which vet clinic? robert

My dealer Impact Guns, delivered the M4 LE package as promised on 12/20. I consider myself very fortunate as only a few pieces shipped complete with the +2 mag extension(no longer available), and the barrel is the heavy magnum twin port version(not "Low Recoil" stamped). [ 01-04-2006, 12:36 PM: Message edited by: jetflyer ]