Celeste Posted May 16, 2019 Posted May 16, 2019 Brand new over-under, after the first time taking it out to a skeet club we attempted disassembly to clean it. To remove the trigger mechanism we used the provided to tool to press and release the trigger guard however we may not have had the strikers in the cocked position. Now the back end of the trigger mechanism is stuck halfway out. Stupid mistake on our part, but was hoping that there was someone out there who ran into the same issue. Any advice helps, only had the thing 4 whole days ? 1 Quote
MrBritish1976 Posted August 29, 2019 Posted August 29, 2019 Did you resolve this I have the same issue ? Quote
Benelligunny Posted September 4, 2019 Posted September 4, 2019 Never attempt to remove the trigger assembly with the top lever open. This will cause a serious jam. If it was not open and just the strikers were out, remove the floating breech per the instructions in the manual , the get the trigger assembly back in place as best as possible and go through the front with a punch or something and push the strikers back in place. Always push the top lever release button on the front of the receiver (near the top lever) before removing the trigger assembly. As always, don't force it or break it. You're not the first to do this. Send it to us if you can't get it and we'll get it out and back in properly. Quote
Bruce H Jackson Posted September 19, 2019 Posted September 19, 2019 Same exact issue. Trigger guard is 5 mm out. Can’t put back and can’t pull out as lever is on the right open) and not closed. Manual does not show how to remove floating breech. Resetting pin does nothing. What next? Quote
Bruce H Jackson Posted September 20, 2019 Posted September 20, 2019 In reference to my post above, when looking at the disassembly video on the website, there is no warning about the open or closed position of the lever. It does say this in the manual, however. That said, this mechanism is firmly jammed just a few milimeters off its seating. Can't push it back in and can't pull it out. Tried light oiling and such, but no effect. Thanks for your insights! Bruce Quote
[email protected] Posted December 17, 2019 Posted December 17, 2019 On 11/4/2019 at 11:25 AM, Greylag said: My 828U cocks the lower barrel everytime I open the gun no matter if the shell is fired or not Anybody know how I could adjust the ejector only to cock when fired? If the trigger assy is stuck out somewhat it is because the gun was not cocked.. remove the breech blopck and use a thin Robertson screwdriver to recock the firing mechanisms.. this will allow you to push the trigger assy back into place ., when removing the trigger assy . cock the gun and them apply the safety ..this will prevent accidental pulling of the trigger when removing the assy . Quote
remarkable Posted December 18, 2019 Posted December 18, 2019 Bruce H Jackson, if you PM me I will assist you. Do not worry, you will be able to install your Trigger group without sending it to Benelli. Mark Quote
Harry Mitchell Posted December 17, 2020 Posted December 17, 2020 On 12/18/2019 at 2:27 PM, remarkable said: Bruce H Jackson, if you PM me I will assist you. Do not worry, you will be able to install your Trigger group without sending it to Benelli. Mark On 12/18/2019 at 2:27 PM, remarkable said: Bruce H Jackson, if you PM me I will assist you. Do not worry, you will be able to install your Trigger group without sending it to Benelli. Mark Hi There, I am having the same problem with my 828. I tried to remove the trigger mechanism without releasing the top lever, the trigger mechanism is now a little out of the breech but I can't get it back or out. Any help would be great! I am in the UK. Quote
remarkable Posted December 22, 2020 Posted December 22, 2020 Please PM me, I could assist. I will be documenting this condition and will photo shoot this in a few days when I see my next 828U. Quote
Upland66 Posted January 17, 2021 Posted January 17, 2021 On 12/21/2020 at 4:59 PM, zarko said: I am also having the same issue Quote
Don fogal Posted April 18, 2021 Posted April 18, 2021 On 12/17/2020 at 1:06 PM, Harry Mitchell said: Hi There, I am having the same problem with my 828. I tried to remove the trigger mechanism without releasing the top lever, the trigger mechanism is now a little out of the breech but I can't get it back or out. Any help would be great! I am in the UK. Quote
Don fogal Posted April 18, 2021 Posted April 18, 2021 1 hour ago, Don fogal said: Can anyone send me the info supplied by Remarkable 1 hour ago, Don fogal said: Quote
Benelli shooter 12 Posted May 23, 2021 Posted May 23, 2021 Can you also send me the info for this same problem Quote
NFranks Posted July 12, 2021 Posted July 12, 2021 (edited) Same situation here. Any help would be greatly appreciated! Update: I got it. Took me a few minutes to figure it out. Edited July 12, 2021 by NFranks Quote
828 Posted October 1, 2021 Posted October 1, 2021 Can you please send me the info too? I tried to take out the triggery with the cock in open position and its stuck and partially out. Please help Quote
828 Posted October 1, 2021 Posted October 1, 2021 43 minutes ago, 828 said: Can you please send me the info too? I tried to take out the triggery with the cock in open position and its stuck and partially out. Please help Update: I managed to fix it. Here is what you have to do. The Manual says if you accidentally activate the trigger guard while trigger disassembly, don't try to force out the trigger assembly. The reason why the trigger gets stuck while removing when the cock lever is in open position because it activates the trigger guard. All you need to do is, push the clock lever further into the open position and with some force of your hand, using the palm, you should be able to push the trigger assemble back into its seat. Do it till you hear the click sound. Then close the clock lever and you will hear the clocking sound. Voila! Quote
Keepitvyle Posted March 26, 2022 Posted March 26, 2022 I have an 828u sport and the trigger mechanism is stuck can someone please help. Quote
remarkable Posted March 29, 2022 Posted March 29, 2022 Please PM me if you are still in need of assistance. Quote
FLShooter293 Posted September 11, 2022 Posted September 11, 2022 Remarkable, can you please send me the info too. I PM’ed you. Thank you in advance Quote
Graham12 Posted December 23, 2022 Posted December 23, 2022 Same issue, seems I just need to locate the firing mechanism and then hopefully the trigger assembly should click back into position and help guys would be appreciated Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.