stockplayer

Yes i did it.....i will try to find pic or take new ones

sure was........I will be sure to give Tom some kudos on this board after all is said and done.

Thanks guys leads were good I have a M2 in jail as I type. Ten days and the build can begin.

I know these things are hard to find......but come on there must be one laying around somewhere? Benelli says 60 to 90 days

check out Daves Metal works for the full length tube. read up on 922r Erik

****, I would even take a 21" m2 in black to do my own build.

What is my best shot at getting one of these? Who is going to get these instock first?

I run my wet with militec and it will shoot even 2 3/4 drams. Wet is the key

Lmt 16" piston in 556 Benelli m4 Les Baer 1911 .45 The same guns i use for IDPA multi gun Proven set up for me

I have had good luck with militec. I cant say it is the best because i have not tried them all but the benelli, les baer, and lmt piston I use for 3 gun and frontsight classes all run perfectly.

All looks good to me. Put it back together and make sure the bolt is nice and wet. Run some full power buck shot through it. I run mine with oil dripping from the insides

Where can i find one of these?

Bump to the top

This tube was made long before all these other tubes were being produced. It was bought off this forum. The color actually looks better than my Benelli factory tube. It was installed and function tested that is it. I bought two thinking I was doing to get another M4. $120.00 http://www.flickr.com/photos/85277486@N00/4911928775/ It is made in the USA therefore it counts as a compliance part. Erik [email protected]

Dont make the rail too short. Play around with some diffrent lengths. the front of the hand guards are tappered.......makes it hard to mount a light up front. that is why mine is so long. Ill try and take some pics soon Erik

Here you go guys http://www.flickr.com/photos/85277486@N00/315360371/in/photostream/ http://www.flickr.com/photos/85277486@N00/315360375/in/photostream/ http://www.flickr.com/photos/85277486@N00/315360369/in/photostream/ http://www.flickr.com/photos/85277486@N00/315360377/in/photostream/ I used a rail with threaded holes. It was a tapered rail for a AR rifle forend. I milled it down and mounted it to my M4 from the inside. Erik

Is an M4 with a non pistol grip stock a sporting shotgun? Also, where can I find an official definition of a sporting or nonsporting shotgun? Thanks, Guys

Diabolus, mabe Duggan came over and cut it? Everyone hurry, get out your exploded diagrams, Diabolis is comming......and you know how he get when we don't have our exploded diagrams out! Chill-lax man

sorry I am just jokin man My bad! You are right, it will not unscrew with the cap on. I need to stop

AR you should have added some blue........on your first shot your benelli will unscrew itself and you will be left holding only the stock and fore-grip. I have seen it happen a hundred times. [ 09-16-2006, 07:15 PM: Message edited by: stockplayer ]

To convert Fahrenheit to Celsius, subtract 32 degrees and divide by 1.8. To convert Celsius to Fahrenheit, multiply by 1.8 and add 32 degrees. Spent some time teaching science

They do not want any sarcasm in this thread

Here is where this thread stands Red stuff-----too strong Green stuff-----too strong Blue stuff-----good option No stuff-----works for some White stuff--------now thats just sick!

Ok fine no locktite is needed Can I take my hat off now? Duggan is right it will not come loose while shooting because of the mag cap. I think I am going to spot weld mine in place. Kind of like when Cortez had his ships burned. There is no turning back. Forward men

just use the fricken blue stuff! gosh [ 09-14-2006, 11:04 PM: Message edited by: stockplayer ]