Jump to content
Search In
  • More options...
Find results that contain...
Find results in...
Benelli Forums

jk6672

Members
  • Content Count

    34
  • Joined

  • Last visited

Everything posted by jk6672

  1. jk6672

    Best Charging Handle?

    Has anyone contacted FFT and voiced their concerns so they can rectify the issue? I have there Ti full tube and think it's rather nice. I also would like a larger charging handle but can't see purchasing the FFT with all the complaints.
  2. I comes out the front end. You twist off the end cap and remove spring retainer clip and spring and it will slip right out.
  3. Sorry to here about your bad experience, hopefully they make it right.
  4. jk6672

    3inch shells

    Went shooting today and put about 50 target load, 50 LR 1oz slugs, 50 00 buck, then 50 3inch 00 buck. Those 3inch (first time using) kick like a mo fo! My shoulder feels it now, kind of like a real hard workout at the gym. Gotta love a good workout, but those shells are no fun to shoot more than a few.
  5. jk6672

    M4 mods

    I have small and large snap ring pliers. where can I find that post and video link?
  6. jk6672

    M4 mods

    Did you change your trigger group yourself? I haven't swapped mine out yet, too hesitant to try myself. Thinking of just pulling trigger group and taking to to local gun smith.
  7. jk6672

    M4 mods

    What foregrip do you have? I love that Surefire foregrip even though it adds quite a bit of wieght, but I'm fine handling the extra wieght. The only thing I want to change now is the charging handle. I'm debating between the steel or Ti FFT handle.
  8. jk6672

    M4 mods

    Thanks. I qual @ 25 with iron sites and agency SG. We can take our personal firearms to the range, but we still need to qual with agency issued. I want to replace my charging handle on my M4. Are there any + or -'s with the FFT steel or Ti handle? I thought I read some neg's about the Ti some time ago, but can't locate the info again.
  9. That is nice. Almost as beautiful as the ETHOS.
  10. jk6672

    M4 mods

    11.5lbs in current form, no shells. I put my Mesa push button sling mount and T-1 on today without Larue mount (in route). I can see the dot fine where I mounted it (not dialed in though). My field of vision is good with both eyes open, no tunnel vision at all. Curious at what yardage most start sighting in their red dot with slugs?
  11. jk6672

    M4 mods

    I'll reweigh it. I put the Surefire M900L on it. I like the quick disconnect on it.
  12. jk6672

    M4 mods

    Thanks for the info. Believe me, I have no desire to have it fixed, but I have no desire to be in hot water for manufacturing an AW in California. One of the dumbest laws passed in Ca, I scatch my head when I think to myself what were these lawmakers thinking when they outlawed collapsible stocks on a semi auto shotgun. It's ok on pump, it's ok on Semi auto rifles. I wish they would reverse that one.
  13. jk6672

    M4 mods

    Have you done that mod? I though about that too, but I thought the button would be hollow with spring against pin.
  14. jk6672

    M4 mods

    What mount did you use? I'm going with the LaRue low mount. I can go out to middle, but middle is perfect for iron.
  15. jk6672

    M4 mods

    re-installed cheek rest.
  16. jk6672

    M4 mods

    used a Ti button head screw to disable stock adjustment button.
  17. jk6672

    M4 mods

    I ordered a T-1 today and fixed my stock in the fully collapsed position. I took the the cheek rest off and drilled straight down throw the stock and into the button for adjusting stock length.
  18. jk6672

    M4 mods

    Lift some weights. Kidding.... It's not bad, at least for me. just bought Surefire M900L and will be ditching the current foregrip
  19. jk6672

    M4 mods

    What mount is good for fully collapsed? I like shooting the irons in the middle, but want to shoot fully collapsed too. With the Larue mount can you remove the T-1 easily? Heck who knows, maybe once I use a red dot I may not want to use iron again. ) how do you like that sling? I want a sling and have never used a sling that mounts at a sing point.
  20. jk6672

    M4 mods

    I put the OEM collapsible stock on and love it. I want to try the T1, do I need a mount (i.e. Larue) or does it just mount to the picatinny rail?
  21. Thanks H&K for OEM collapsible stock. The middle position is perfect for iron sights. I want to add micro T1, will fully collapsible work well with red dot? I can't use iron sights fully collapsed.
  22. jk6672

    Calapsable stock

    Never mind. Easy swap
  23. jk6672

    Calapsable stock

    I bought a colapsable stock for my m4. How do I replace if?
  24. I like my Benchmade knives. They don't make mine anymore. The HK auto-axis and autostryker. I have a Spyderco, but it's more of bought it for looks than anything else. It's a little folding knife with the spyder cut out in a web on the blade and whole handle.
  25. I'm in no way knocking CC, but seeing all the wait times I ordered a FFT Ti and within two weeks it was on my M4. I couldn't be happier with the quality.
×
×
  • Create New...