_RomeoAlpha Posted February 2, 2021 Share Posted February 2, 2021 (edited) Hey Benelli fam, I’m planning to finally shoot my new M4 for the first time in a couple of days. In preparation, I disassembled and CLP’d as instructed. Assembling things back in place, I noticed I scratched the inside of the receiver/ejection port. It’s surface level..but I just want to know if this is a common/“normal wear and tear” scratch or if I did something wrong and should prevent it from happening again. This is my first firearm so I’m pretty bummed I already made “character” marks without actually using it yet. I know it’s going to be put to work but just want to know if I should be protecting it better, if it needs to be treated or repaired, or to not worry about it at all. Any tips and advice would be appreciated. Thanks! Edited February 2, 2021 by _RomeoAlpha Addendum Quote Link to comment Share on other sites More sharing options...
Shekkie Posted February 2, 2021 Share Posted February 2, 2021 Are you sure it isn’t just grease? Not sure what you could have done to scratch it like that there and not notice. Quote Link to comment Share on other sites More sharing options...
_RomeoAlpha Posted February 3, 2021 Author Share Posted February 3, 2021 Yeah, I’m sure it’s not grease. I got it from sliding the barrel back in place into the receiver. I didn’t notice it until I took it apart again to place a hand guard. Quote Link to comment Share on other sites More sharing options...
Nocturnalnature Posted February 3, 2021 Share Posted February 3, 2021 Check the bottom corner of the barrel extension for a burr or rough machining. The good news is your receiver will get more wear marks that correspond with the barrel extension as you shoot it so the scratch won't stand out as being abnormal or accidental in nature. Eventually it will simply blend in with the honest wear and tear. 1 Quote Link to comment Share on other sites More sharing options...
Scout_21 Posted February 3, 2021 Share Posted February 3, 2021 Like others I wouldn't be too concerned... there will eventually be a fair amount of wear in that area and other parts. I don't see this being a huge issue as that's where the bolt carrier will be operating. StrangerDanger would probably know best with his knowledge of many m4s... I just have two at this point Otherwise maybe just check the pins in the bolt carrier and manually push it against the rear to see if it slides easily. Check to make sure the "tail" is seated against spring piston and before you put in the bolt handle. But please to be careful with fingers as things can pinch and the receiver extension spring can be quite stiff. 1 Quote Link to comment Share on other sites More sharing options...
_RomeoAlpha Posted February 3, 2021 Author Share Posted February 3, 2021 That’s good news. I’m sure I messed up by having the bolt already dropped before sliding the barrel back in place. ?♂️ Quote Link to comment Share on other sites More sharing options...
Scout_21 Posted February 3, 2021 Share Posted February 3, 2021 Well the bolt does need to be in before attaching the barrel... I generally don't have it cocked when sliding the barrel in though. 1 Quote Link to comment Share on other sites More sharing options...
BallChange Posted February 4, 2021 Share Posted February 4, 2021 I've got something a line like that in mine, but I have ~800 rounds through mine. If there's no issues when you shoot it, I really doubt it's anything to worry about at all. 1 Quote Link to comment Share on other sites More sharing options...
Tuck Posted June 30, 2021 Share Posted June 30, 2021 I put a scratch in that same area just by cycling dummy rounds through it for practice. I was using AZoom snap caps and I did notice the paint coming off around the edges of the them. Now I have cleaned it thoroughly and got all the paint chips out. No more practice for me.. Time to go and fire some live rounds. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.