Dkay67 Posted October 15, 2021 Share Posted October 15, 2021 Took my M4 apart to send some parts to Wright for NP3 coating, and thought I'd check out the recoil assembly tube to verify putting a spare non-Np3 together before selling it. Well, imagine my surprise when I saw this... It shoots okay, but that's not the issue. Quote Link to comment Share on other sites More sharing options...
Treetommy Posted October 16, 2021 Share Posted October 16, 2021 I could have done that for half price?. Seriously though at least your tube doesn’t look scratched up. I believe the boogered up part is the Stock Retaining Screw. They’re only about $26 at Midwest. I’d be annoyed also but it’ was a cheap lesson, if you decide to find a new smith. Quote Link to comment Share on other sites More sharing options...
Doge Posted October 16, 2021 Share Posted October 16, 2021 (edited) big oof. Exactly why I made my own screwdriver since I never found a decent one off the shelf. There should really be a M1014 armorer's tool in the box of every brand new M1014. Edited October 16, 2021 by Doge 1 1 Quote Link to comment Share on other sites More sharing options...
Dkay67 Posted October 16, 2021 Author Share Posted October 16, 2021 1 minute ago, Doge said: big oof. Exactly why I made my own screwdriver since I never found a decent one off the shelf. There should really be a M1014 armorer's tool in the box of every brand new box. Thing is, its not that difficult to screw in on its own, even under spring tension. There's also supposed to be a snap ring to prevent the screw from walking out. I've tried different ways to get something to bite on the going areas, but I can't tell if the threads have been treated with locktite or not as there is no give at all to back it out Quote Link to comment Share on other sites More sharing options...
Doge Posted October 16, 2021 Share Posted October 16, 2021 So there was no snap ring inside? I was under the impression the screw was all damaged and that was the issue. You don't need the thread locker on this screw. It should unscrew easily. Quote Link to comment Share on other sites More sharing options...
Dkay67 Posted October 16, 2021 Author Share Posted October 16, 2021 4 minutes ago, Doge said: So there was no snap ring inside? I was under the impression the screw was all damaged and that was the issue. You don't need the thread locker on this screw. It should unscrew easily. I realize no thread locker, but I don't know if this gunsmith used it because its very tight and almost ripped a thumb nail trying to remove it with a piece a metal that fit into the tooling points. It doesn't appear he even compared the removed normal finish tube assembly to build the NP3 assembly. I dont even know if he inserted the retaining ring in the front of the tube with what I've seen done in the rear Quote Link to comment Share on other sites More sharing options...
Doge Posted October 16, 2021 Share Posted October 16, 2021 It can be a burr on the threads, I've seen it often on the tubes. Quote Link to comment Share on other sites More sharing options...
Dkay67 Posted October 16, 2021 Author Share Posted October 16, 2021 (edited) 3 minutes ago, Doge said: It can be a burr on the threads, I've seen it often on the tubes. Whatever it was, it should have been communicated to me of the issue. Its a integrity factor as well as a safety issue. You don't just slap the collapsing stock on it and hope the poor assembly isn't discovered on a $3000 plus shotgun Edited October 16, 2021 by Dkay67 Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted October 16, 2021 Share Posted October 16, 2021 Is it possible the gunsmith put the snap ring inside the tube rather than on the outside of the plug? Quote Link to comment Share on other sites More sharing options...
Milspec Posted October 16, 2021 Share Posted October 16, 2021 Was this done by Benelli? Quote Link to comment Share on other sites More sharing options...
Dkay67 Posted October 16, 2021 Author Share Posted October 16, 2021 2 hours ago, Milspec said: Was this done by Benelli? No. A local gunsmith to my location. Previously good work. Returned the shotgun with stock on to conceal the shoddy work. Only discovered when stock removed to cross reference for a assembly of another complete tube. 1 Quote Link to comment Share on other sites More sharing options...
bambihunter Posted October 25, 2021 Share Posted October 25, 2021 Take it back in and see what he has to say about it. Quote Link to comment Share on other sites More sharing options...
Dkay67 Posted October 25, 2021 Author Share Posted October 25, 2021 1 hour ago, bambihunter said: Take it back in and see what he has to say about it. Thats what I did, but seeing that SD is now in full pheasant season I'm having a bit of delay and, expected locating and delivery of a to better suited to removing or installing the screw Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.