I have a Benelli M4 H20 and want to put a red dot on it. Any ideas how to do this with a 1/3rd co witness

[Jaason0]

I have a Benelli M4 H20 and want to put a red dot on it. I do not like an absolute co witness. Would like to see if anyone has a set up that they re doing a 1/3 rd co witness

[Unobtanium]

The Scalarworks SYNC will give you what amounts to a lower 1/4 co-witness, basically.

[Jaason0]

thanks man I ll check them out. I assume you have the one with the rmr? Can you get on target pretty easy ? I guess i m  asking can you get on target easily without the irons affecting your sight pic too much

[Unobtanium]

2 hours ago, Jaason0 said:

thanks man I ll check them out. I assume you have the one with the rmr? Can you get on target pretty easy ? I guess i m  asking can you get on target easily without the irons affecting your sight pic too much

I run higher mounted optics. I prefer closed emitters and use T series. The irons are not a detriment, but neither do I find as much value in a cowitness, so this is how I set my benellis up.

[Jaason0]

I like that. I don t care about co witness and want to see as much of thee window as I can. I like your set up a lot, Thanks

 

[Ben elLes]

I also like the high optic it makes the middle position of the stock feel natural.  

[Unobtanium]

2 hours ago, Ben elLes said:

I also like the high optic it makes the middle position of the stock feel natural.  

Yes, and under nods, I run the stock fully extended and its perfect for that, too. True no/low and daylight dual setup. 

[Evolution]

Hey Unobtanium, what MOA Aimpoint do you run and which mount is that? Thanks!

[Unobtanium]

8 hours ago, Evolution said:

Hey Unobtanium, what MOA Aimpoint do you run and which mount is that? Thanks!

Thats a 4moa H2, a hold over from before I got NODs. Ironically, when I turn it off, its like setting 3 of 4 NV on a T2 under nods. Now, Id recommend a T2 2moa.

 

The mount is an ADM Ti mount in CAS-V height.

 

The rail is an FFT.

 

This combo has had good RTZ, and tolerated recoil from anything Ive thrown at it, including a fair bit of 3" 00b.

Edited July 13, 2022 by Unobtanium

[StrangerDanger]

You can also remove the iron sights pretty easily. I find they clutter the optic and add extra unneeded weight.

 

Decide which stock position you want to use primarily. I find the RMR to sit too low for the middle position of the collapsible stock. Fully extended it works fine. You can buy a spacer that fits between the RMR and the Scalarworks mount to raise the optic from Reptilia. They have 2.5mm and 10mm options depending on your preference. You'll have to modify the screw that come with the spacers to fit the Scalarworks, basically you're just shortening them to the needed length.

This one is set up with the 10mm spacer.

Edited July 13, 2022 by StrangerDanger

[Evolution]

18 hours ago, Unobtanium said:

Thats a 4moa H2, a hold over from before I got NODs. Ironically, when I turn it off, its like setting 3 of 4 NV on a T2 under nods. Now, Id recommend a T2 2moa.

 

The mount is an ADM Ti mount in CAS-V height.

 

The rail is an FFT.

 

This combo has had good RTZ, and tolerated recoil from anything Ive thrown at it, including a fair bit of 3" 00b.

Thanks partner!