Jaason0 Posted July 10, 2022 Share Posted July 10, 2022 I have a Benelli M4 H20 and want to put a red dot on it. I do not like an absolute co witness. Would like to see if anyone has a set up that they re doing a 1/3 rd co witness Quote Link to comment Share on other sites More sharing options...
Unobtanium Posted July 10, 2022 Share Posted July 10, 2022 The Scalarworks SYNC will give you what amounts to a lower 1/4 co-witness, basically. 1 Quote Link to comment Share on other sites More sharing options...
Jaason0 Posted July 10, 2022 Author Share Posted July 10, 2022 thanks man I ll check them out. I assume you have the one with the rmr? Can you get on target pretty easy ? I guess i m asking can you get on target easily without the irons affecting your sight pic too much Quote Link to comment Share on other sites More sharing options...
Unobtanium Posted July 11, 2022 Share Posted July 11, 2022 2 hours ago, Jaason0 said: thanks man I ll check them out. I assume you have the one with the rmr? Can you get on target pretty easy ? I guess i m asking can you get on target easily without the irons affecting your sight pic too much I run higher mounted optics. I prefer closed emitters and use T series. The irons are not a detriment, but neither do I find as much value in a cowitness, so this is how I set my benellis up. 1 Quote Link to comment Share on other sites More sharing options...
Jaason0 Posted July 11, 2022 Author Share Posted July 11, 2022 I like that. I don t care about co witness and want to see as much of thee window as I can. I like your set up a lot, Thanks 1 Quote Link to comment Share on other sites More sharing options...
Ben elLes Posted July 12, 2022 Share Posted July 12, 2022 I also like the high optic it makes the middle position of the stock feel natural. Quote Link to comment Share on other sites More sharing options...
Unobtanium Posted July 12, 2022 Share Posted July 12, 2022 2 hours ago, Ben elLes said: I also like the high optic it makes the middle position of the stock feel natural. Yes, and under nods, I run the stock fully extended and its perfect for that, too. True no/low and daylight dual setup. Quote Link to comment Share on other sites More sharing options...
Evolution Posted July 12, 2022 Share Posted July 12, 2022 Hey Unobtanium, what MOA Aimpoint do you run and which mount is that? Thanks! Quote Link to comment Share on other sites More sharing options...
Unobtanium Posted July 13, 2022 Share Posted July 13, 2022 (edited) 8 hours ago, Evolution said: Hey Unobtanium, what MOA Aimpoint do you run and which mount is that? Thanks! Thats a 4moa H2, a hold over from before I got NODs. Ironically, when I turn it off, its like setting 3 of 4 NV on a T2 under nods. Now, Id recommend a T2 2moa. The mount is an ADM Ti mount in CAS-V height. The rail is an FFT. This combo has had good RTZ, and tolerated recoil from anything Ive thrown at it, including a fair bit of 3" 00b. Edited July 13, 2022 by Unobtanium 1 Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted July 13, 2022 Share Posted July 13, 2022 (edited) You can also remove the iron sights pretty easily. I find they clutter the optic and add extra unneeded weight. Decide which stock position you want to use primarily. I find the RMR to sit too low for the middle position of the collapsible stock. Fully extended it works fine. You can buy a spacer that fits between the RMR and the Scalarworks mount to raise the optic from Reptilia. They have 2.5mm and 10mm options depending on your preference. You'll have to modify the screw that come with the spacers to fit the Scalarworks, basically you're just shortening them to the needed length. This one is set up with the 10mm spacer. Edited July 13, 2022 by StrangerDanger 2 Quote Link to comment Share on other sites More sharing options...
Evolution Posted July 13, 2022 Share Posted July 13, 2022 18 hours ago, Unobtanium said: Thats a 4moa H2, a hold over from before I got NODs. Ironically, when I turn it off, its like setting 3 of 4 NV on a T2 under nods. Now, Id recommend a T2 2moa. The mount is an ADM Ti mount in CAS-V height. The rail is an FFT. This combo has had good RTZ, and tolerated recoil from anything Ive thrown at it, including a fair bit of 3" 00b. Thanks partner! 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.