alphat Posted September 22, 2022 Share Posted September 22, 2022 (edited) I purchased Daves Metal Works "Tactical Bolt Handle" for Benelli M4. After installation, I notice that the handle can rotate. Depending on how I manipulate it (support hand, under the gun), it can rotate more, to the point of coming out and falling from the bolt carrier during dry fire. The same is happening with OEM handle. Is there a solution to that? Are there any aftermarket bolt handles that do not rotate? Edited September 22, 2022 by alphat Quote Link to comment Share on other sites More sharing options...
RxArms Posted September 22, 2022 Share Posted September 22, 2022 This might have more to do with your bolt detent and spring specs than the charge handle. some newer M4 for whatever reason the detent is not traveling as far into the charge handle hole, which can cause issues. your detent and spring might need servicing, you can also try sticking a spacer with the detent spring which will increase the pressure of the detent. what model is your gun? Quote Link to comment Share on other sites More sharing options...
ThisShouldDoTheJob Posted September 22, 2022 Share Posted September 22, 2022 14 hours ago, alphat said: Is there a solution to that? Are there any aftermarket bolt handles that do not rotate? They all rotate but some have more pronounced and more angular detents than others. Others have more shallow more universal detents that appear to run uniformly all around the end of bolt handle. If you study the different options out there, you will see what I mean. So far I've had good luck with this one ... https://botach.com/kz-benelli-m4-oversized-charging-handles/ That said, it is more worrying that the OEM one is falling out. Not cool at all and I'm sorry to hear that. All good now, I had my own woes with OEM Benelli parts on my gun. Manufacturing standards and tolerances are in a sad state of affairs these days. Quote Link to comment Share on other sites More sharing options...
alphat Posted September 23, 2022 Author Share Posted September 23, 2022 Mine is Benelli M4 Tactical - 11715. Is there a proper way to insert a charging handle? Generally, I push/rotate it until it's in and give it a pull to make sure it's seated. Quote Link to comment Share on other sites More sharing options...
ThisShouldDoTheJob Posted September 23, 2022 Share Posted September 23, 2022 (edited) Based on the diagram below for removing the bolt handle by first rotating it to the right, you could try rotating it to the left after inserting it. But it should it naturally rotate to the left when you pull it back. @RxArms - who knows a lot more about Benelli products than me - probably has the right answer above in that the manufacturing standards/tolerances are off. You are probably doing everything right. If this continues, I would contact Benelli for a repair because there are few things more seriously wrong than a bolt handle falling out of a gun! No bolt handle, no bang. In fairness to Benelli, they took care of me by covering the shipping costs when I had to return my barrel to have the magazine cap retaining spring and pin re-staked after they just fell out of it and onto the floor before I even fired the gun. I hope this helps. Best wishes for a successful resolution. Edited September 23, 2022 by ThisShouldDoTheJob Quote Link to comment Share on other sites More sharing options...
RxArms Posted September 23, 2022 Share Posted September 23, 2022 16 hours ago, alphat said: Mine is Benelli M4 Tactical - 11715. Is there a proper way to insert a charging handle? Generally, I push/rotate it until it's in and give it a pull to make sure it's seated. Since OEM is very loose and sloppy I agree you should contact Benelli for a new complete bolt carrier. 2 Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted September 23, 2022 Share Posted September 23, 2022 Either the bolt handle wasn’t machined correctly or the detent is damaged. Benelli would be the first stop to see if you can get them to warranty it. Getting the detent out of the bolt carrier is not an easy task. It takes specialized punches and finger dexterity that approaches the insane. Even roll pin holders are of no use since the pin is so short. The punch is so small that they’re easy to break. Getting that tiny pin out without damaging anything is one of my least favorite Benelli M4 jobs. Getting it back in without damaging the spring it retains is even worse. Quote Link to comment Share on other sites More sharing options...
RxArms Posted September 23, 2022 Share Posted September 23, 2022 I’m actually happy I have a bit of a loose detent on one of my M4 for product testing purposes. It is 2020 year production. My other M4 is older with OEM aluminum trigger guard, and that bolt is built beautifully with full detent pressure. Quote Link to comment Share on other sites More sharing options...
Nomaspescado Posted September 24, 2022 Share Posted September 24, 2022 (edited) Mine has been back to Benelli twice now, and with a new BCG the charging handle is still not tight, and is free to rotate about 30 degrees. Better than before, but still not snug as probably intended. Prior to sending in, I had replaced the charging handle, detent, spring and detent with the same results. I think that the recess in bolt body has been drilled too shallow...and is preventing the detent from extending far enough out to engage the charging handle with full-time spring pressure. Edit: Aside from that pesky charging handle, I love this gun. *Shout out to StrangerDanger for positing up so much useful info. His post on replacing the receiver extension gave me the confidence to take it on. Thank you! Edited September 24, 2022 by Nomaspescado Adding something positive 1 2 Quote Link to comment Share on other sites More sharing options...
alphat Posted September 28, 2022 Author Share Posted September 28, 2022 I did some more testing, and the issue may not be as bad as I initially thought. The charging handles - both OEM and aftermarket need some force to rotate. The problem usually happens when I rack the bolt under the gun. If I am not paying attention, my finger can impart some rotational force while moving my hand away at the end. This is what caused the handles to come out. When inserted, the handle doesn't come out if pulled in a straight direction, away from the bolt. I will be going to a three-day shotgun class. Will see how it does there. Quote Link to comment Share on other sites More sharing options...
gocards Posted September 28, 2022 Share Posted September 28, 2022 Egads! As a new customer who just received my M4 LE, this is not inspiring confidence in Benelli. The USMC's use of this rifle was a key reason I purchased my 11732. I found that instructions for assembly were not up to date for the 11732 (had to figure some things out that were not covered in the manual) and my charging handle was awful to remove. Gorilla strength pulling finally got it out, then I put some gun oil on it and worked it a few times before it would release relatively easily. Taking it to a more experienced gunsmith before firing to ensure I covered assembly correctly. I'm new to shotguns and wasn't expecting to have to assemble a $2000 shotgun. 1 Quote Link to comment Share on other sites More sharing options...
benelliwerkes Posted September 29, 2022 Share Posted September 29, 2022 On 9/23/2022 at 2:59 PM, StrangerDanger said: Getting the detent out of the bolt carrier is not an easy task. It takes specialized punches and finger dexterity that approaches the insane. Even roll pin holders are of no use since the pin is so short. The punch is so small that they’re easy to break. Getting that tiny pin out without damaging anything is one of my least favorite Benelli M4 jobs. Getting it back in without damaging the spring it retains is even worse. Removing the M4 Bolt Handle Detent Spring Retaining Pin. The key to making the task simple is to de-tension the spring from acting on the pin, very much like for the bolt extractor roll pin removal. The second item is to have a tool to compress the spring away from the pin. I fabricated a fork tool from 1/8” hex wrench, after observing my M4 trigger safety spring tool would fit in the hole and compress the detent spring; the problem was that tool was too long to fit in vise for compression of the spring. The hex wrench was slotted with a Dremel to 0.067”, shortened to fit a polymer tool handle. The tool can then be fitted in the vise to compress the spring freeing up your hands to remove the pin. The pin is removed inside-outward, once de-tensioned a simple small tool such as jewels screwdriver or 1/16” hex wrench can be lightly tapped with a light hammer to begin moving the pin which doesn’t take much force. A right angle pick with slight pressure will complete the pin removal and the pick captures the spring so it doesn’t fly about. Cover the spring hole, remove the pick and extract the detent and its spring. Installation is the reverse. Compress the spring, insert right angle pick, use small pin holding punch to tap the pin in, displacing the pick. Make sure the inside of the pin does not impinge on bolt raceway. Generally, no need for breaking punches or flying springs. 1 1 Quote Link to comment Share on other sites More sharing options...
benelliwerkes Posted September 29, 2022 Share Posted September 29, 2022 ............................. 2 2 Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted September 30, 2022 Share Posted September 30, 2022 Benelliwerks has the best tools. I imagine all the tools are in special boxes with labels like the Toy Story 2 guy that rebuilds Woody! Your vice is pretty similar too, I have the Wilton 1745 Trademan. I paid $495 for it back in 2018. I just priced one now since things have been built back better, and apparently my vice should be in the safe since it now goes for $1,014.00. 🤨 1 Quote Link to comment Share on other sites More sharing options...
RxArms Posted September 30, 2022 Share Posted September 30, 2022 12 hours ago, benelliwerkes said: ............................. I’m going to have to bookmark this one. Nice write up! Quote Link to comment Share on other sites More sharing options...
benelliwerkes Posted September 30, 2022 Share Posted September 30, 2022 (edited) Finally got around to installing a Wilton 500S 5" vise and installed smooth jaws, it weighs 98 lbs, got it earlier this year. The only one Wilton makes still made in USA. I wanted the 6" but it weighed 150 lbs! The small roll pin holders are made on the lathe which is handy to create short pin depths and small diameters which are easier to control in the hand. I made this 5/32" last week. Edited September 30, 2022 by benelliwerkes 1 Quote Link to comment Share on other sites More sharing options...
benelliwerkes Posted September 30, 2022 Share Posted September 30, 2022 (edited) ............make the punches from drill rod stock. The common roll pin holders are tool long for a lot of situations. Nothing worse than working with a crummy tool in the hand. Edited September 30, 2022 by benelliwerkes 1 Quote Link to comment Share on other sites More sharing options...
benelliwerkes Posted September 30, 2022 Share Posted September 30, 2022 (edited) This set of parallel punches is unique in that the shaft slides along the length of the punch, so only a minimal amount of small diameter punch is unsupported that limits the likelihood of bending or breaking punches like SD mentioned. The Brownells set is useful sometimes, but as in this retaining pin situation, the shaft diameter was too large to fit in the narrow confines of the bolt access. For starting and finishing some pins where a tapered "starter" punch can not be used for whatever reason, I made a set of short shaft punches and hardened the tips which avoids bending and breakage. Edited September 30, 2022 by benelliwerkes 1 3 Quote Link to comment Share on other sites More sharing options...
benelliwerkes Posted October 1, 2022 Share Posted October 1, 2022 In deference to SD I did label it and tuck in to to a labeled drawer. That polymer tool shown above was a Flintstone appearing workhorse but I finally got around to making a more refined tool today worthy for the tool box. Used a shortened #28 drill bit shank slotted with 1/16" square end mill to press fit into a 3/8" drill rod tool shaft cut to length, ends radiused for aesthetics on the slotted end and to be functional fitting into vise jaw hex fastener to stabilize the tool to prevent it sliding down the vise jaw face. Quote Link to comment Share on other sites More sharing options...
benelliwerkes Posted October 1, 2022 Share Posted October 1, 2022 ................. 1 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.