Leaderboard

I have a bunch of shotguns and a few SBS included in those, so i didnt need this shorty but since when has a 'need' really mattered? A buddy from BUDS called and told me they had finally gotten in some TAC-14s in wood and i went down and grabbed one. I added a Mesa saddle and an old Remington sling. I put 50 rnds of 00 buck thru it and its loosened up nicely. It might just end up being my stand in the corner, bump in the night go to.

Very pretty, love the wood! I have a couple Shockwaves I use for rattlesnake dispatchers and they are very effective. Enjoy it

thanks. i like the Shockwave as well but im more of a Remington fan when it comes down to the two. that being said, i may still pick one up before too long

my post from 2021 Posted October 28, 2021 back in late spring/early summer i had a safety failure in my 11707 purchased in 2007. i called, sent the trigger group in for repair. They emailed me with their findings stating that it was a 'very rare failure' and they were sending me a whole new trigger group. I requested that my aluminum TG be replaced with an aluminum vs plastic and they agreed. about a week later i received my new parts with a detailed explanation in writing and everything is right in the universe again.

https://cleanfit.com/blue_monster_ptfe_thread_seal_tape_70885.shtml

I will say this an like me you do a lot of duck hunting, I did notice from my montefeltro lined up perfect with my M2 I noticed the rib on the top of the barrel on my M2 is not flat like the montefeltro the M2 starts to rise from the front of the barrel an gradually gets taller at the end of the barrel I'm hopping that's what it is cause I had the same problem, if the birds were flying that morning I had my limit no more than an hour, I'm actually working on it now, I have a buddy ylthat just got the a300 Beretta an his gun is shooting high

Did Benelli send you the patterning results after the gun was shot at Benelli USA? Did they include any comments about the results they established during the test shooting? Here is a image of established pellet counts. Remembering the pellet count is taken from the center of the 6" circle target.

Shameless plug… I’d like to throw my offering into the ring, it keeps the weight of the handle at the OEM weight, 12g, while giving a much bigger handle for operating. Ti handle and stainless steel tang to prevent wear from the detent. (https://rxarms.com/product/benelli-m4-titanium-steel-tactical-charging-handle/) the TTI handle weighs 28 grams, although I do admit they have a nice design, at the sacrifice of weight. The GG&G 3/4” steel weighs around the same. this year I’ll be offering my design in 4140 hardened steel also. Estimated to be around 17-18 grams, and same locking design (which is similar to TTI locking). Probably in June 2022 I will have stock

Just picked up a Benelli SBE3 in 3" with 28" barrel this week. I was worried about all the past input from owners whose patterns where really high, with most looking like 100% above point of aim. Just wanted to show what a sample of a current model (3" chamber) is shooting. I patterned it from a rest at 25yds with 3 shots to get a good average. The circle is 30" and I was using the factory full choke. 67% above point of aim, 33% below. To me, that's about perfect for waterfowl hunting. It all worked for me yesterday while hunting in some really rough conditions (Iceded over water so just passing birds and 8 degrees). I will obviously need to shoot it a bunch more, but initial impressions are good. 6DA920EB-C084-42F8-9023-FC1B7BBCE08D.heic 152CB3F6-2774-471E-887B-EA6FB0DB3833.heic