-
Posts
580 -
Joined
-
Last visited
-
Days Won
10
Everything posted by Vertigofirearms
-
-
I can confirm M2 20 gauge is shell latch is the same 12 gauge shell latch.
-
Bumping this thread as I was informed by Stranger Danger that people have been trying to modify the shell latch. I was working on converting a ethos shell latch to be backwards compatible with the older receivers until I came across a few threads about this. The one that sticks out to me is from bsp212 on the Briley loading port thread. Coincidentally, I had ordered the the Rob Roberts modified 20 gauge shell latch before I saw this thread. So I will have 2 different 20 gauge shell latches to see. Late into my research, I discovered Briley manufactures a two piece milled shell latch, but it requires enlarging the receiver hole.
-
Finally had time to visit the range. Brought a few M3s, one of them was failing to release shell from mag tube....?
-
Benelli M4 -- Shell Stop Removal & Install
Vertigofirearms replied to StrangerDanger's topic in Benelli
I remember doing that once?. Ordered a set of nice punches and never looked back.- 33 replies
-
- 1
-
- benelli m4
- bolt release
-
(and 2 more)
Tagged with:
-
It is still pretty amazing how many Benelli parts are still backwards compatible. I wished Benelli would have an online resource center to check parts fitment.
-
Does any body know where to get these parts?
Vertigofirearms replied to Butters149's topic in Benelli
Hensoldt RSA-S. I have one on mine. BTW that is Sigma05's Benelli. -
http://www.shotgunworld.com/bbs/viewtopic.php?f=61&t=391968 Benelligunny is most likely correct. I dug up a deep archive of a post I replied to before and sure enough there is a picture of the two choke tubes. SL80 choke tube.
-
Does anybody run their M4 without the top rail?
Vertigofirearms replied to forzArmata's topic in Benelli
I like the clean look. I think I might go this route -
Not easy to remove. Buy the best roll pin punch you can afford.
-
Oh you are correct. If you want it to be easily removable you will have to cut some metal. You could also install the M1014 single position tube.
-
Pretty much you take the stock apart and drop a pin in. You can reassemble or modify the button to be easier to limit. https://www.calguns.net/calgunforum/showthread.php?t=1507997 Another option:
-
If you go that route, you can buy an extra button in the event you mess up the hole. https://www.midwestgunworks.com/page/mgwi/prod/70093
-
Looking to buy the M4 plastic trigger guard
Vertigofirearms replied to Vertigofirearms's topic in Benelli
pm sent -
If you got an extra, I would like it. Online appears to be metal still.
-
There is likely something just slightly misaligned causing the hang up. Make sure nothing is protruding out of the trigger assembly.
-
did you cock the hammer?
-
hold the bolt release button down, then push the trigger in.
-
Rotate it a bit, play around with it. Get to know your gun.
-
Your Super nova has the same spring for both trigger pins. The Ethos has two as well, but only one is used to keep the pin in place.
-
Part number is 60504. It is literally the only spring holding your troublesome trigger pin in place. If it is not that then you may need to put in a warranty request.
-
I love the M4 lifter as well. I believe it is in the Ethos and Raffaello, just chrome plated. I am having several M4 lifters cut to fit in my M3.
-
Already like the XS sight more. I dunno if I will ever use it because my rig is set up for a red dot and has a cheek riser.
-
I never knew they were that expensive!
-
Installing a Limbsaver 10403 on a Benelli M4 Collapsible Stock
Vertigofirearms replied to StrangerDanger's topic in Benelli