Fullassault

Thanks! It should be here tomorrow after a 800 mile detour today…

Do the FCG part swap over to the aluminum TG or will I need aluminum TG Specific parts?

QC was a little rough on my 2020 M3 but my 2021 M4 is perfect inside and out.

Haven’t heard anything about oem trigger guards, People were having issues with the A&S not long ago. That’s actually why I decided to grab one of these for $50 less

I assume the aluminum is stronger than the polymer TG.

FYI, they are sold out.

Just got a notification from MGW that they have aluminum trigger guards in, just grabbed one for $140

922r us Titanium tube, us follower, trigger & hammer. that said I asked the ATF a few years back about 922r and the one who replied back said 922r only applies to the manufacturer. Some people don’t care about it, some follow it religiously. Honestly it’s not something I stress over too much. If the US parts ever give me trouble, I’ll switch to oem parts and never think twice about it.

The flag and the M1014 roll mark for me!

Don’t know what the status of the “limited” part of the edition but correct on the other differences.

Get on the list while you look. https://www.midwestgunworks.com/page/mgwi/prod/70043

With the ACRO just dropping & M5 using The lens geometry and technology from the T-2 a T-3 might be some time off.

The T2 will give you a clearer image and battery life of around 4-5 years of constant on. the RMR has a very good battery life too but it also has the fiber optic/ tritium option. Both are battle tested, both will serve you well. Cowitness has its draw backs. If your optic gets damaged or muddy both sight and irons are out of commission. If you run a low mount on the rail all you need to do is flick a lever and you have your irons. personally I run a low QD mount RMR because I like running the stock collapsed. I have a BKC front sight and the triangle RMR.

The stock isn’t bad, it’s much less complicated than the M4 stock. The M3 is interesting but I much prefer the M4

Owned both the M3 & M4 (can’t speak for the M1) Out of the 2 the M4 is much better IMO! The M3 is not as reliable in SA and is awkward as a pump. The M4 has been 100% reliable with everything including low brass junk that chocked the M3. Also the M4 is better balanced, much easier to take down and actually has aftermarket options. That said the M3 isn’t bad, I just wouldn’t pick it over the M4…. For any reason… To each their own….

This is mine (2021 M1014)

Have the KZ , seems to have plenty of clearance.

Spf

Price drop $208 shipped

Obo

After a 5mo wait I got my new Carrier Comp tube so I’m selling my used one. The previous owner cooked the paint a little so I covered it with a custom foil label. This section is under the hand guards. Function perfectly in my M1014 total round count 25 from original owner & 50 from me. $230 shipped

I’m using a RMR & Blitzkrieg front sight on mine. I’m going with the great triangle of death theme.

I got the M1014 because of the designation, I found one of the 3 position extension for $80 so it was a easy choice for me. Had the whole project finished in 2hrs at a total cost of $2200 - the RMR. (Nib M1014, Extension, CC ti tube, and a few other parts)

I’m waiting on a S&W 500 mag to get back from S&W (8 to 14weeks). Purchased it new a week ago , the front sight fell off, discovered two loose cylinder locks and the entire inside is covered with rust and red oxide.

I don’t have a CF tube but I haven’t had any trouble with ti or steel tube w/o any thread locker. As long as the end cap is on the tube isn’t going anywhere.