ccwinmemphis Posted February 24, 2007 Posted February 24, 2007 Does anyone have instructions for installing the collapsable m4 stock and pistol grip on an 11707 m4. thanks in advance ! Brian Quote
HOGWILD Posted February 24, 2007 Posted February 24, 2007 click on Customer Service on Benelli home page then click on manuals and if that's not enough help i will reinstall tape!! pg. 35 and 36 Good Luck in advance!! Quote
HNLV Posted February 24, 2007 Posted February 24, 2007 You should open up your usermanual and turn to page 59. It will tell you how to do it. #1. Remove barrel #2. Remove slide #3. Remove Trigger #4. Remove screws inside the recoil pad. Two really small holes. #5. Remove Hex nut with 1/2 socket(deep or extenstion will work). #6. Remove the stock by turning it counter-clock wise. *** now just reverse the steps with the new stock.*** Quote
Full Bore Posted February 24, 2007 Posted February 24, 2007 Hogwild is correct. HNLV is not. There are no screws or nuts to be removed at all. Just the trigger assy. Heres the link to the manual. Pg 36. I own an M4 with all the stock configs. Thats the beauty of the M4. No tools to quickly change stock configs. http://www.benelliusa.com/customer-service/pdfs/M4Super90.pdf Quote
aga7040 Posted February 24, 2007 Posted February 24, 2007 You should open up your usermanual and turn to page 59. It will tell you how to do it. #1. Remove barrel #2. Remove slide #3. Remove Trigger #4. Remove screws inside the recoil pad. Two really small holes. #5. Remove Hex nut with 1/2 socket(deep or extenstion will work). #6. Remove the stock by turning it counter-clock wise. *** now just reverse the steps with the new stock.*** Full Bore is correct. I don't know where/what HNLV's directions are for. Quote
Scott R Posted February 24, 2007 Posted February 24, 2007 First get a hammer, a heatgun and a tire jack. Now put that stuff down and read Hogwild's post. I've changed mine and did not use any tools. Quote
HNLV Posted February 25, 2007 Posted February 25, 2007 Hogwild is correct. HNLV is not. There are no screws or nuts to be removed at all. Just the trigger assy. Heres the link to the manual. Pg 36. I own an M4 with all the stock configs. Thats the beauty of the M4. No tools to quickly change stock configs. http://www.benelliusa.com/customer-service/pdfs/M4Super90.pdf Yes i was wrong. steps 4 & 5 isnt needed Quote
Full Bore Posted February 25, 2007 Posted February 25, 2007 Just for clarity, you don't need to remove the barrel or bolt either. Just the trigger group so you can turn the stock off, and of course make sure its not loaded. As I said before thats the beauty of the M4. No tools and simplicity for easy stock config changes. Quote
HOGWILD Posted February 25, 2007 Posted February 25, 2007 It is just a matter of plain old ENGLISH if ya can read or search for a manual ya pretty much gotter whupped!! Sorry for the poor english i am a native arkanite!! But do wear shoes now and duct tape did not work AH's Quote
Thunderbolt Posted February 25, 2007 Posted February 25, 2007 Yes i was wrong. steps 4 & 5 isnt needed Neither are 1 & 2. Quote
BEAR_ICE Posted February 26, 2007 Posted February 26, 2007 Listen to Hogwild and Full Bore. My wife and I each own one (11707) they are beauties. It took me a bit to figure out the trigger group is what locked it in place. Then I was able to unscrew the stock. Quote
ccwinmemphis Posted February 26, 2007 Author Posted February 26, 2007 Thanks everyone for your help. I got her in and she is sweet. Very simple, just remove the trigger group and twist counterclockwise, then reverse. On another note, what do you guys do to clean the gas pistons after shooting. I took one apart and it was a b_tch to get back together. I won't be going there again. Quote
Varangian Posted March 10, 2010 Posted March 10, 2010 Okay, hate to gravedig but I can't figure out how to get the collapsible buttstock on. I have a 3-position tube, but I don't need to do any turning to get it to go on or come off. I just keep the button depressed and it slides right on...and off. How do I install this so that it doesn't just slide right off if I keep the button depressed? Quote
Varangian Posted March 16, 2010 Posted March 16, 2010 Got 'er figured out. Many thanks to Texas Skeeter for the kind donation of his time and knowledge! Quote
ROCKETW19 Posted September 12, 2010 Posted September 12, 2010 pm sent....... Why on earth would you send a PM? some of us use the search function,lol I didnt read any directions I have no time for that stuff now my stock is on wrong,lol and I can get it back off lol I am stupid Quote
texas skeeter Posted September 12, 2010 Posted September 12, 2010 Damn Rocket, could ya have dug up an older thread???? Quote
ROCKETW19 Posted September 12, 2010 Posted September 12, 2010 Damn Rocket, could ya have dug up an older thread???? this was the first one that poped up with search. I have the camo version M17017 or what ever code but I can only get my Cstock to be full length or closed all the way. I thought there was a middle position? Is it on wrong? Quote
Super33 Posted September 12, 2010 Posted September 12, 2010 this was the first one that poped up with search. I have the camo version M17017 or what ever code but I can only get my Cstock to be full length or closed all the way. I thought there was a middle position? Is it on wrong? Sounds like you just have to find that sweet spot in the middle. There's 2 notches in the middle, one is to hold the stock in the center position and the other is for installing/uninstalling the stock. There's also 2 lines (rings) going around your tube. Line up the front of the stock with the rear line to install/uninstall the stock. Line up the front of the stock with the forward line for the center collapsed position. I hope this solves it. Quote
Jackalope33B Posted September 27, 2010 Posted September 27, 2010 This link should work.. http://www.benelliusa.com/assets/manuals/Benelli_M4_Super_90_manual.pdf Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.