Pack Rat

Agreed. I would expect no less from him on the m4 platform.

I use a TTI reduced power hammer spring. It's worked well so far (no ftf)

A+ transaction. Much appreciated,SD

Inquiry sent

Hello,folks. I'm looking for a new or gently used Scalarworks SYNC for a aimpoint micro. Let me know. Thank you.

Been gone a while. Back to necromance this thread for Les Garten- You can run that elzetta with some bicycle inner tube around the tailcap of your Bravo.Torqe a pound or two extra. The tailcap is tapered and scallopped so back it out towards the stock a bit beforehand.The innertube fills the gaps and gives more surface area engagement. I also added friction tape to the under side of the mount where it interfaced with the barrell.Mines been hanging tough for a couple yrs and hasn't budged in the first AVA mount...and I shoot the m4 quite a bit. I believe elzetta machined the lights for their mount or vice versa. Either way this setup is viable.Good Luck Les

I wanted to check in and let it be known that the elzetta bravo works well in this mount as long as the low-pro bezel and 1" ava ring are utilized.

Loctite...? Never heard of it! Permatex surface insensitive and anaerobic primer are a winning combo.

I went w/ the G-brand because the Lbrand was too low for me to get a proper cheek weld in the middle position using the c-stock. You'd probably need a tall mount if you're running it fully collapsed. Also the weight of the gbrand isn't anything I've noticed after switching out the L-brand mount.

What size if you don't mind me asking?

I also use a T-1 (2moa). I couldn't see myself running anything larger or heavier on an m4. The larue mount I had was slightly too low. I switched to a GDI. With the stock in the middle position the aimpoint's exactly where I need it to be. I finally put a couple (50-75 remy slugs, rio buck) rounds through it last week & everything ran perfectly (even with the reduced power hammer spring). I like the ghost ring (sorta) but but love this red dot. It's never coming off my m4.

I see. Thanks, Joel .

Yes,Joel. it's 1.46".

I'm interested in the mount but don't believe the torch I have (elzetta bravo AVS) will work with it. I do believe a fury specific mount would work though. The malkoff low-pro head isn't something i feel i need. This mount on the other hand.... If anyones running a AVS Bravo I'd appreciate your feedback on compatibility. Thanks in advance.

I got them from a m a z o n but midway & brownells probably have them too. Yeah, I used a small clamp (meant to hold paper work together) to hold the carrier latch in place against the receiver & a straightened paper clip as a slave pin.

These hold up well . I used em on the bolt pad I installed & some trigger group work as well. I wasn't very easy on them with the mallet either. http://www.amazon.com/Grace-USA-Steel-Spring-Punch/dp/B007WADKN0/ref=pd_sim_sg_2/186-6394337-3455506?ie=UTF8&refRID=1BGPFAGRG4EWN86RR8QD

Yeah,man. I got the safety,hammer spring & "shell elevator" as well. All dropped in (the m4) & function smoothly.

cool. your reviews are decent.

Hear,hear ! Benelli m4... All killer no filler !

Nice! count me in,please.

yea,SD...they fit. Hammer spring is the ****. http://forums.benelliusa.com/attachment.php?attachmentid=2414&d=1387651030

just make sure you have decent 5/64 roll pin punch before you get started.

Thanks. I appreciate the hospitality,Bhunted.

Thanks,SD. Thanks for the writeups on how to actually sling the m4 (with a c-stock) as well.