Jump to content
Search In
  • More options...
Find results that contain...
Find results in...


  • Content Count

  • Joined

  • Last visited

  • Days Won


Everything posted by aznwhip

  1. Weight Any mlok mount will work. I'm partial to quality of Arisaka mounts though. Didn't try SRO, but did play around with an RMR and T2, both on Scalar mounts. I preferred the RMR, bit that's personal. Both were fine and quality. Sling. Trigger. CF tube if you're chasing weight savings. Follower honestly doesn't matter much. It holds the spring and pushes the round. Not rocket science. Just get one made in the US as they're all pretty much the same. If you buy their trigger, only they can install the trigger. They won't send it to you to install.
  2. Got any sketch diagram of design? Edit: nevermind, saw it on your site.
  3. Yeah, maybe they improved it, but the one I had (and I know StrangerDanger had the same problem) was too wide for the OEM spring restrictor. If Briley didn't make an update and you bought from an ebay retailer.... might question their authenticity. I'd hope not, but coming from aftermarket automotive world... CF parts are the easiest and most prolific counterfeits out there. Especially with the length problem... that seems fairly obvious and knowing Briley, I can't see how that would have escaped their QC.
  4. Either a defect or they sent you the wrong one. Either way, contact them. Also, you were able to fit the spring restrictor in the tube? One I had was too wide to use that so spring was held down by the cap.
  5. Yes, I get that... However as far as I know, there's no simple bolt on option for such. The Briley guard us the closest thing to what he's looking for as a bolt on. It allows for flipping and grabbing over the barrel (or laying on his shoulder) to load. The guard wraps mostly over the barrel.
  6. Briley handguard wraps around the barrel to serve as heat shield.
  7. I have a Modlite Modbutton Lite. That was just an older picture I found to showcase clearance to answer a question.
  8. No, it would still hit from my testing. The height provided by the pic rail on the IWC mount and the pic connector on the light are greater than the lip of the cap and remaining gap.
  9. I was able to luckily score an Agency handguard which fit my hand better.
  10. Not nubile virgin tight, but not main street corner girl loose either lol It's honestly not bad.
  11. You have to use the pic mount for the tail to clear the guard.
  12. Yes, the 8" handguard will work fine with the iwc mount and an m600. That was my exact setup at one point. You can check out on the Benelli M4 picture thread.
  13. I've done slingsters, Trex, MS1... Keep coming back to BFG Vickers.
  14. Yeah, lasted a whole 15 minutes from what I was tracking. Hopefully some 1014 owners here were able to get it.
  15. Bought mine from benelliparts without issue.
  16. https://www.midwestgunworks.com/page/mgwi/prod/70130 This came across my feed and know some are looking for it. Cheaper than benelliparts
  17. For light shadow requirement.... The decision is kind of already made for you then with the 13" Briley. However, that also runs counter to your weight shedding ethos you've been chasing, so you'll have to weigh (pun intended) what's more important. For my hands, it came down to ability to comfortably control muzzle rise. Since the Briley rail basically goes straight up on the sides till it reaches and wraps around the barrel, I was relying on friction to hold the barrel flat. With the Agency, since it doesn't wrap around the barrel, it curves in lower, which allows me to wrap my thumb an
  18. Options will vary, but for my hands, the Agency guard feels the best and has great function and aesthetics. I had the Briley one before the Agency so was able to compare those two (along with stock obviously). The problem is finding one as they're currently also unicorns unless you send it in for a full build. I was extremely lucky to score mine.
  19. Might be able to plastidip it yourself as well. Was toying with the idea as a cheap and completely reversible option. It's not hard to disassemble to get cerakote or professionally painted. Main thing is to let Briley get all the parts installed and function tested to ensure QA/tolerances of parts are solid. Assembly and disassembly afterwards can easily be performed.
  20. Love it. Agency does great work. Just wish they'd allow an a la carte to their build.
  21. Just get their black trigger shoe to cover it up. I will say the short LOP version is F'n amazing.
  22. I think the shell guide is kinda gimmicky. This coming from a quad loader. I do like the metal vs polymer which gives me a bit more confidence (perceived or otherwise) in allowing me to run it hard without durability concerns banging it around.
  23. I had it for a spell... Solid guard. Tight tolerance. I liked that it wrapped over the barrel so you don't burn you hands when flipping to load.
  • Create New...