Huff64 Posted September 7, 2012 Share Posted September 7, 2012 I guess ill break down and order my CC full tube today. These M4's are rapidly becoming money pits. $1600 for the shotgun, $350 for a C-stock, $180 for a tube. And I still want a red/green dot site system, sureshell shell carrier and maybe a 3 point sling. Guess I need to start playing the lotto. LOL. Quote Link to comment Share on other sites More sharing options...
Amsdorf Posted September 7, 2012 Share Posted September 7, 2012 I had a Sureshell carrier ordered, but cancelled after thinking more about it. I think I'm going to go with a Sideamor Mod 4 system. Quote Link to comment Share on other sites More sharing options...
Zeke Posted September 7, 2012 Share Posted September 7, 2012 Zeke, yes on the snap ring pliers!! Will make your life a lot easier. Can't wait to see the results of your install, enjoy!! It's fun. Make sure you get this kind of snap ring plier set: http://www.sears.com/shc/s/p_10153_1...d Toolsmv=rr The snap ring in the tube needs to be squeezed together to remove and reinstall, so if you get a "dual purpose" snap ring plier, you'll have more options. I got mine at Home Depot, Vice Grip brand, not very expensive. Done deal, I went to Home Depot on lunch today and picked up a snap ring plier very simular to your pic, but mine is made by Channel Lock. Also picked up some Acetone and heat gun and balsa wood. Im ready !! Got another 3 week wait though. Quote Link to comment Share on other sites More sharing options...
tucker301 Posted September 8, 2012 Share Posted September 8, 2012 Zeke, Be sure and take before and after pictures and post them back here, along with an account of your experiences. Quote Link to comment Share on other sites More sharing options...
Zeke Posted September 8, 2012 Share Posted September 8, 2012 Zeke, Be sure and take before and after pictures and post them back here, along with an account of your experiences. OK... whats the deal with downloading photo's?? Is there instructions somewhere? Quote Link to comment Share on other sites More sharing options...
Zeke Posted September 8, 2012 Share Posted September 8, 2012 (edited) [ATTACH=CONFIG]1629[/ATTACH][ATTACH=CONFIG]1630[/ATTACH][ATTACH=CONFIG]1631[/ATTACH] Nevermind.. I figured it out...........These are before pictures! I still have a 3 week wait before my CC Tube gets here. Edited September 8, 2012 by Zeke Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted September 8, 2012 Author Share Posted September 8, 2012 Recommend you replace the top rail with the carriercomp true spec unit. Quote Link to comment Share on other sites More sharing options...
FLAWLS1 Posted September 9, 2012 Share Posted September 9, 2012 I read you didn't put locktite on the threads. How has it been so far? Has it loosened up after several rounds? I think I may install mine without locktite. Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted September 9, 2012 Author Share Posted September 9, 2012 The magazine cap keeps it seated. I've never had it loosen on me. I tend to shoot a lot each session. Usually 300-400 rounds. Just crank the tube down with both hands. Quote Link to comment Share on other sites More sharing options...
FLAWLS1 Posted September 9, 2012 Share Posted September 9, 2012 The magazine cap keeps it seated. I've never had it loosen on me. I tend to shoot a lot each session. Usually 300-400 rounds. Just crank the tube down with both hands. Thanks for the reply. I'll install it without the locktite too then. Quote Link to comment Share on other sites More sharing options...
Hookster Posted September 9, 2012 Share Posted September 9, 2012 Thanks for the reply. I'll install it without the locktite too then. +1 I've never used LocTite on the tube... No loosening issues Quote Link to comment Share on other sites More sharing options...
Sukhoi_fan Posted September 9, 2012 Share Posted September 9, 2012 Hossed mine down strictly by four hands, no threadlocker used and no loosening issues. (of course one should periodically check it when one fully breaks down one's M4 for a thorough cleaning, however I don't see how it's going to become loose without threadlocker) Quote Link to comment Share on other sites More sharing options...
Amsdorf Posted September 9, 2012 Share Posted September 9, 2012 The factory uses it to install the magazine, and CC recommends using it when replacing the tube, so....I figured it is a good idea to use it. LOCKTITE BLUE (the stuff that comes in a red tube, go figure). Quote Link to comment Share on other sites More sharing options...
KB Fab Posted September 9, 2012 Share Posted September 9, 2012 +1 I've never used LocTite on the tube... No loosening issues I didn't use any either. No need really as there isn't much chance of anything loosening up provided that you have put everything back correctly. I like that is makes a full disassembly easier. Quote Link to comment Share on other sites More sharing options...
Guest cleefurd Posted September 9, 2012 Share Posted September 9, 2012 I don't use it, and only recommend doing so deferring to factory intent, which is much more practical than inserting a disclaimer about the possibility of loosening. There are advantages to both approaches, and I too like the unfettered abilty to conduct full disassembly on a moments notice, so I skip the use of loctite. If I were headed to an event or scenario where extensive daily use or training were taking place, I would strongly reconsider reversing my personal stance. It is more "worry free" if loctited, and that prudence is the main reason I recommend the average owner use loctite. Reminds me of my Stihl chainsaw. There are two types of chains available... a sedate variant that cuts well but won't kick back, and a "Saber Tooth" variant that makes short work of timber, that will kick back and maim the uninitiated user. It is up to the end user to decide what works best for his/her level of attentiveness to aggressive hand tightening, routine observation of the assembly status, and how easy they prefer complete disassembly remain. I realize it would be much easier to choose one approach and ignore the other, but I know both methods have merit, and try to assure that either will suffice, and that a choice exists. The one involving loctite is like using a seatbelt... tedious, but down the road, under less than ideal conditions... arguably favorable. Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted September 10, 2012 Author Share Posted September 10, 2012 (edited) When I removed the receiver extension, it took a lot longer to break the thread locker. It took about 30 minutes to break the lock nut free. Then another 30 - 40 minutes to get the receiver extension to budge. When I reinstalled my new three position extension unit, I applied a lot of red locktite to both the receiver extension and the lock nut. It would be a bad day at the range to have the receiver extension unscrew on you during recoil. Fortunately due to the ingenious design of the Benelli stocks, only the tail section of the collapsible stock can put any torque on the receiver extension. The pistol grip is indexed in place by the trigger group. About 2000 rounds later, I haven't had any issue with it. I may be pulling it off in the near future though. I got a hold of a second 3 position receiver extension. My loose plan is to send it and the plunger off to WMD guns and have them coated in nickel boron.I just have to get off my butt to mail the parts to them. My loose goal is to increase the cyclic rate through reduced friction. I'll be happy with even a marginally improved lock time. Edited March 20, 2013 by StrangerDanger Quote Link to comment Share on other sites More sharing options...
Zeke Posted September 15, 2012 Share Posted September 15, 2012 Still waiting for my CC Tube...............THis is kiling me! Quote Link to comment Share on other sites More sharing options...
Amsdorf Posted September 16, 2012 Share Posted September 16, 2012 How long has it been since you ordered it? Quote Link to comment Share on other sites More sharing options...
Duggan Posted September 17, 2012 Share Posted September 17, 2012 This thread made me smile. Good memories. Quote Link to comment Share on other sites More sharing options...
Zeke Posted September 17, 2012 Share Posted September 17, 2012 How long has it been since you ordered it? I placed my order Aug 29th.........still waiting Quote Link to comment Share on other sites More sharing options...
58sniper Posted February 9, 2013 Share Posted February 9, 2013 So after two attempts to get the magazine off, I took a short break, then decided one last attempt for the night. Full blast of the 1200 watt heat gun for 12 minutes, and it finally broke loose. Some people mention that they see green thread locker, and some people say they have red. Mine was clearly red. Glad I finally got it off. Much easier putting the new tube on! Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted February 9, 2013 Author Share Posted February 9, 2013 Glad to hear that it worked out for you 58sniper. Interesting about the various types of thread locker applied by the factory. Quote Link to comment Share on other sites More sharing options...
Macfly Posted November 18, 2013 Share Posted November 18, 2013 Man! Videos make that look so easy....clearly not so. i bought a wagner digital heater ( other type they made only has two settings, one low and one higher) this one went up to around 1250 f or so. Started out like te instructions said at around 450. At first i didnt have a vise so was trying to do it holding the receiver in a towel clamped in my knees with my dad trying to turn. Was not budging so i upted it to around 750. After heating fir maybe 10 minutes the whole receiver was starting to get really hot and the tube budged slightly. Red loctite. finally gave up and got access to a vise. Basically had to hit it with around 1000 for a few minutes before it started to turn and i just kept the heat on while dad kept turning. But that was not something i could have done alone.. Muche easier with two people. but now the new tube is on and looks great. So now i can go walk around with thise two extra rounds and know how much money and effort went into it! Quote Link to comment Share on other sites More sharing options...
burntorangefan Posted November 18, 2013 Share Posted November 18, 2013 Hi everyone, new member here...Got my M4 a couple of weeks ago and did my research...after emailing Kip to check on availability and being presented with that scenario, I opted to go FFT Titanium tube with new forend and follower from FFT as well. I'm pleased with the results and with this guide everything was very easy to do...Thanks again! Quote Link to comment Share on other sites More sharing options...
JASON4X4 Posted November 18, 2013 Share Posted November 18, 2013 I didn't have much trouble replacing my tube. About 10 min with the heat gun and it came off easy Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.