Milspec

I did not specifically request that they take the stock apart and plate the internals. So , I'm assuming that they will not. Honestly, I didn't even think of it. I plan on getting the collapsible down the road when I relocate. I did request that they plate everything else though. Especially the recoil tube/extension.

Yikes! That definitely looks like a PITA. I guess running the rear QD on the opposite side would be a no go with that much butt stock behind it.

Are their any good QD sling mount options available for the M4 pistol grip stock? (non collapsing) I don't want anything that is installed between the receiver and the stock. (like mesa tactical/GG&G options etc)

It looks like NP3 has a hardness range of 48-51 rc which is a little tighter spec range than NP3+ which appears to be 35-50. I guess it's a roll of the dice where your hardness ends up with the NP3+. I wonder if I should call them and have it switched to NP3.

Sweet! Did you have those done in NP3 or NP3+? I sent my M4 and other parts in to them this week. They seem very organized over there. The day it arrived they sent me a quote and had the job logged in their system with in 5 1/2 hours of receiving. Time to wait and squirrel away more cash to pay off the other half. Based on SD's wait time I figure I have about 4/5 months. Thanks again to SD for all of his help. A lot of guys that have his level of knowledge aren't nearly as forthcoming with sharing. He saved me from sending in my CC mag tube for no reason.

What hand guard/forearm is that?

Anyone else want to let one go? Lol

Bump-$375.00

Brand new in the box. Still sealed in plastic. These are excellent, top of the line mounts. $385.00 shipped PayPal F&F/Gift or US Postal Money order.

Yes, BD. I changed it over to the A&S 3/4 months ago. I don’t remember having an issue with the trigger bushing. My main challenge besides the safety roll pin was the snap ring that retains the bushing. I didn’t have a good quality pair snap ring pliers at the time. I had some difficulty removing that bushing snap ring. Since then I invested the $20+ and upgraded my pliers.

Mine went together pretty well. The roll pin that holds in the detent and spring for the safety was stupid tight. Really out of control stupid tight. I also purchased the lightened safety spring. Although it could be a hair stiffer for my taste, it’s much better than the OEM. The factory safety spring is not that user friendly IMHO.

Where did you come across the mil spec 18.5"?

It would be nice if Scalarworks made an option for the DP Pro.

Very interesting set up. I have a Venom on my PCC.

Thanks SD. That's what I was afraid of. I'm curious how my Aimpoint Acro would co witness on the OEM rail.

I saw one from Midwest Industries but the photo is terrible. I've also seen what Scalarworks has. I'm just trying to find out what rail options are available. I don't want anything with a shell carrier attached to it.

Crazy stuff. Thanks for the info. I like their mounts just not a fan of the Trijicon RMR. However, the SRO has the same screw alignment as the RMR. The down side is the SRO is not nearly as tough. I don’t know if it would stand up to the recoil.

Not to boss hog in on the OP’s thread but I’d like to buy a Sync mount for the Ainpoint Micro T-1 etc. I’m assuming Scalarworks discontinued them. I can’t seem to find one.

Does anyone know how the CC mag tube in “muted” matches up to the NP3 finish? They say it’s pretty close but I haven’t heard from anyone who actually has seen or owns one.

Thanks SD. It seems my H2O dream is just getting too difficult to chase. I may have to go the route of Midnight or Burnt Bronze Cerakote.

SD, does Wright Armory disassemble like Robar use to? Or does everything have to be broken down? I know you bust everything down, I’m just wondering what’s their method of operation. I know they say Ti can’t be plated but I’m wondering if they would do a mag tube and simply not warranty the finish?

What QD are you running in the stock?

I had a local shop do it for me. They are more of a 1911 custom place but they know what they are doing. I went way conservative compared to most. If you saw it you would probably think it wasn’t opened up enough. While this would be true to most I didn’t want to go too aggressive. I’m not a three gunner, just wanted to make reloading a little easier and efficient. At the same time I wanted to retain the tactical integrity without making it too sporting like. I hate throwing out the word “tactical” but I think it applies here. I messed around with it a little bit and was able to dual load a couple times. I’m sure with some practice and getting use to it I could be more proficient. Perhaps quad loads in the future but like I say it’s a modest opening. Overall I’m happy with it but I wish they rounded it off more where the mag tube begins and the follower lies.

No worries. It was a good lead. It’s not your fault. Thanks for bringing it up as a possibility.

I’d like to be first on the list. Lol My loading port job has been completed so I’m ready.