d Posted April 27, 2011 Posted April 27, 2011 Good Morning, It has been two years in the making but I finally have it finished. This is real not photo shop. comments are apprecated. Thank you, D Quote
Ilintner Posted April 27, 2011 Posted April 27, 2011 That is f'ing awesome. Do you plan to put the front sight back on? Quote
d Posted April 27, 2011 Author Posted April 27, 2011 That is f'ing awesome. Do you plan to put the front sight back on? It would be to difficult to resolder it with out discoulring the barrel. I think I am going to put a small red dot like a doctor optics on it, with a ten inch barrel I will not need long range accurace. I also have a laser sight mounted under the barrel (you can barely see it in the picture.) It has three adjustable laser dots that are adjustable and I set them for my pattern at 15 yards. Regards, d Quote
twowheelhooligan Posted April 27, 2011 Posted April 27, 2011 That's just sickly friggin' awesome!!! Nice work! I would install a tactical spork as a bayonet on the front! Nicely done!! 2-wheel Quote
xamoel Posted April 27, 2011 Posted April 27, 2011 Great work! How sensitive is it to different ammo? Quote
M4Madness Posted April 27, 2011 Posted April 27, 2011 That is f'ing awesome. Do you plan to put the front sight back on? It would be to difficult to resolder it with out discoulring the barrel. I bet it wouldn't cost much to have Victor at US Anodizing reparkerize the barrel -- probably less than $50. http://www.usanodizing.com/ That's a sharp-looking weapon. If we could have SBS's here in Indiana, I'd be all over it myself. Quote
KB Fab Posted April 27, 2011 Posted April 27, 2011 (edited) I'm looking at doing this very same thing but having King Armory do the work. It should be easy enough to re-solder the front sight using ribbon silver and just the right amount of heat on the sight lug. The real question I have is.............are you using a 2 or a 4 port barrel. Are you having any cycling issues at all? Looks sweet but I think I would want the front sight on mine. One more question, what did you do, if anything, for the mag cam detent? Or did you just simply tighten the mag cap against that hand guard lug? If so, does it work loose when firing? Thanks! Edited April 27, 2011 by KB Fab Quote
d Posted April 27, 2011 Author Posted April 27, 2011 1, rubber thin o ring to replace the detent. Two port gas system, fire 2.75 and 3 inch and have no problums. 2. Capicaty is six 2.75 inch shells with a carrier load. 3. It it is senstive to ammo. I primarly use magnum loads but it will cycle with #4 3?. Regards, d Quote
d Posted April 28, 2011 Author Posted April 28, 2011 I need a extreamly high streangth adhere to attach a front sight to SBS Any help is I thank you. Regards, d Quote
Monkey Posted April 28, 2011 Posted April 28, 2011 Sorry, I think it needs the front sight. Looks unfinished. Quote
KB Fab Posted April 28, 2011 Posted April 28, 2011 Sorry, I think it needs the front sight. Looks unfinished. Agreed. Also, if you have the ability to measure (with dial calipers), would you be willing to determine the final thickness of the end of the barrel? Also, while you are at it, could you measure the inside diameter at the barrel end? Thanks man. Quote
Tango two Posted April 28, 2011 Posted April 28, 2011 Nice job. Is the silver tab on the pistol-grip to attach a sling to? Quote
d Posted April 28, 2011 Author Posted April 28, 2011 Agreed. Also, if you have the ability to measure (with dial calipers), would you be willing to determine the final thickness of the end of the barrel? Also, while you are at it, could you measure the inside diameter at the barrel end? Thanks man. Of course, I would like to put on the mep light front sight I have. I have calipers and will do a compleate measurment of center of bore to back sight. I just do not want to mess the finish. Regards, d. Quote
d Posted April 28, 2011 Author Posted April 28, 2011 Nice job. Is the silver tab on the pistol-grip to attach a sling to? Sorry, need more info. Front or back attachment? Regards, d. Quote
AggiePhil Posted April 28, 2011 Posted April 28, 2011 This thread is weird. Sorry, had to say it. Quote
heckler&kochp2000 Posted April 28, 2011 Posted April 28, 2011 Were did you buy the tactical jack Stands? Quote
d Posted April 28, 2011 Author Posted April 28, 2011 Who's forend is that? Custom, made them my self. Quote
d Posted April 28, 2011 Author Posted April 28, 2011 Were did you buy the tactical jack Stands? Hah! I was waiting for for you to chime in. Good old harbour freight. Quote
d Posted April 28, 2011 Author Posted April 28, 2011 This thread is weird. Sorry, had to say it. God bless the USA and all it's freedom to be weird. Quote
heckler&kochp2000 Posted April 28, 2011 Posted April 28, 2011 Hah! I was waiting for for you to chime in. Good old harbour freight. It was only a yoke Quote
needncash Posted April 30, 2011 Posted April 30, 2011 Spell check is your friend. Look at the title, 2 errors . Benelli not Benneli.......also, completed not compleated. Quote
AggiePhil Posted April 30, 2011 Posted April 30, 2011 (edited) Spell check is your friend. Look at the title, 2 errors . Benelli not Benneli.......also, completed not compleated. I'm glad somebody else noticed it too. Edited April 30, 2011 by AggiePhil Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.