tucker301

Ok, so you're smallish, but strong and in good shape. Benelli offers shorter recoil pads for us shorter fellows. http://www.benelliusa.com/firearms/partsAccessoriesPads.tpl Benelli makes some great selections in LH models, so you're in the right place with regards to that. You can also change the cast on a RH model, using supplied shims and plates, to better fit a LH shooter. Inertia guns use kinetic energy from recoil to cycle the action. Overall, the system can be very reliable and easy to maintain. However, since the system does rely on recoil, there can be problems if the gun isn't shouldered properly or if light loads are used. All Benelli semi-automatic sporting guns are inertia (recoil) operated. Benelli guns are also lightweight guns. Weight is the only thing an inertia gun has to scrub off recoil before it reaches the buttpad. A good pad can further dissipate recoil through compression. A mercury recoil reducer can add weight and uses some kinetic energy to lessen recoil when using heavier loads, but it may make cycling of lighter loads unreliable. Gas operated guns divert a portion of the muzzle blast energy back into the bolt to cycle the action. Since gas is diverted from the muzzle, there is less actual recoil and therefore less felt recoil. Gas guns are a little heavier and have more moving parts, and typically require more maintenance . By far we see more new owners complaining about the recoil of the Benellis than any other factor. It's simple physics. The lighter the gun, the less recoil will be scrubbed off setting the gun into motion. At this point, I would strongly recommend that you shoot a Benelli or two before spending money on one. I'm 5'9 and probably not in as good physical condition as are you, but the recoil of my 3.5" hardly ever bothers me. I don't shoot much target, so when I'm shooting, I'm killing... or at least trying to. If I shot a lot of clays, I'd probably get a gas gun for that.

Recoil is a pretty simple concept. There are two things that lessen actual recoil. The weight of the gun, and re-directing gas in a direction other than straight out of the muzzle. A gas gun of otherwise equal weight will have less actual recoil than will a pump, inertia, or break open gun. Recoil and felt recoil can be reduced with the use of several aftermarket products. Mercury recoil reducers and weight and use kinetic energy to lessen actual recoil, while advanced shock absorbing pads can reduce felt recoil by dissipating its effects over time and area. To be honest, I don't think the Comfortech system reduces recoil nearly as effectively as a nice mercury reducer and a good pad. A mercury reducer on an intertia gun can cause problems because the inertia system relies on recoil to function. I can hold my SBEII at the hip and fire it, and it won't cycle light loads at all. That's because there's no solid resistance to make the action perform properly. All recommendations are good. If it were my son, I'd go with the pump for the reasons stated. I just don't think an 8 year old is mature enough for a semi-automatic weapon.

One post, over two weeks ago. Looks like a drive-by.

Cynergy and Xtrema2. You came out OK, despite the poor genetics .

I wouldn't start an 8 year old with anything more advanced than a pump gun. It's like learning to drive a stick before going to the automatic, and it's safer for others. He has to conciously work the action to chamber another round, so he knows there's one in the chamber and he won't easily forget it. You don't want to a gun that will beat the kid to death and make him afraid or uncomfortable to shoot it. Inertia guns, Comfortech or not, are lightweight and they kick harder than just about any other kind of gun there is. Nova short stock or 870 youth in 20 guage.

What gun have been shooting? What do like about it? What do you dislike about it? Have you disassembled and cleaned any shotguns? How tall are you? How big are you? How strong are you? Are you bothered by recoil? Are you right-handed or left-handed? You like the way the Benelli feels. Please elaborate. Is it the weight, the fit, pointability or all? Do you understand the essential differences between gas-operated guns and inertia-operated guns?

Brownells shows both a drop change shim and drop lock plate designated LH and RH. They probably shipped them with each gun respectively, but not as complete kits the way the SBEII's are done. The cast is going to either come from the lock plate being drilled off-center or the drop shim being thicker on one side than the other. Matt, if you could check that when you get home and post back, perhaps our friend could only purchase the exact part(s) needed to change the cast.

If you need a better understanding of the installation, you can read the discussion between buthwhat and myself here . CAUTION! Thread contains posts by HOGWILD and may cause headaches if those parts are read

The kit's the same for both sides. The cast plate is reversed to achieve cast on for LH shooters. No wonder you couldn't find one

The chart below shows the kinetic energy of various shot sizes at various ranges. At 40 yards, #5 shot is packing around 3.5 ftlbs. of energy. I'd say that's enough to break through the feathers from the back or side, but it would be iffy on making a recoverable kill unless the spine were hit properly. Head-on, with the shedding properties of the layers of feathers, I'd say the chances are marginal. Even if the shot manage to pierce the outer layers, there's a lot of breast meat and bone protecting the vitals. More than likely, you'd end up with a wounded bird that would be difficult to recover.

'cause that's what men do!

Clipped this from the local rag this evening. Is it any wonder no one trusts the media these days?

Nice lawn! I would have to agree with sdkidaho, however on taking the long shot. Too risky.

You answered your own question. 200 rounds. After 200 rounds, shoot at or above the recommended minimum load. Inertia guns aren't made for light trap and field loads. If you want a light load gun get a gas gun like the Beretta.

Don't tug on Superman's cape.

I'm not sure I fully grasp what you're saying is going on, but make sure the threads are cleaned and lubed. Most Benelli dealers sell the choke tube wrenches with the thread cleaners on them. A good investment. I'll check mine when I get home and see if there's a brand name on it.

I know you stated it was for mudhen, but you did post it publicly. I'll just point out the obvious and leave the rest for mudhen. There are more pellets in the 6's than in the 5's, so yes the density should go up.

Between the crappy weather and the Coyotes, we're having a hard time with 'em here. I'm working on the cure for the Coyotes Savage 12FVSS 22-250 50 grain Vmax over 4895 5 shots @ 100 yards Pesky crosswinds opened up the group a bit, but I think my POA/POI are close enough for old Wiley.

jerry, Which model?

Earlier SBEII models were not drilled and tapped, so there are such models out there.

Contact laserlyte. Either the Beretta QD mount or the Universal mount should work. They should be able to tell you for sure.

Interestingly enough, I got the cert. in the mail exactly one year after he was banded.

Once again, mudhen and others have discussed these subjects here at great length. Take some time and go through the forums or use the search feature.

Craig, Yes a better fitting gun will result in a slight reduction felt recoil, but don't expect too much. The Benelli is a lightweight, non-gas driven shotgun. There's simply very little there to scrub off recoil. Marketing is marketing.

Read posts in these forums by mudhen