Jump to content
Search In
  • More options...
Find results that contain...
Find results in...
Benelli Forums
heckler&kochp2000

BENELLI OPTIC RAIL The decisive Trijicon RMR mount for the Benelli m4

Recommended Posts

I have a SuperVinci. If I install your rail will I still be able to have clear line of sight on my factory beads with the MRDS removed?

I'd like to have the flexibility to take off the MRDS for waterfowl/upland hunting.

 

We don't have a SuperVinci to test, but by looking at photos of it I'd have to guess that the rail would obstruct your view of the front bead, assuming you use your normal cheek weld.

Share this post


Link to post
Share on other sites
Have you guys considered offering this mount for the Burris Fastfire III?

 

There are lots of good optics out there and one day we might get to supporting them all, but for the foreseeable future we're committed to Trijicon and Aimpoint.

Share this post


Link to post
Share on other sites

I got my m3 back today with the BOR/RMR installed. Pretty happy with the finish product. Need to take it to the range and zero it next!

IMG_0163.jpg

IMG_0164.jpg

IMG_0165.jpg

Share this post


Link to post
Share on other sites

We were doing an installation of the Scalarworks rail with a Trijicon RMR 06 on Thursday for a client with a M1014 model M4. We torqued the screws to the factory spec 18 inch pounds. When we went to install the barrel, the second from the rear fastener was extending into the receiver and preventing the barrel from seating freely. We apply Loctite primer to both the threads on the receiver and the fastener. Then Loctite 243 to the fastener's threads.

 

We ended up using one of the factory washers on that fastener to allow the proper torque applied. Not a big deal really. Just an anomaly.

 

Is this something you've encountered before?

Share this post


Link to post
Share on other sites
We were doing an installation of the Scalarworks rail with a Trijicon RMR 06 on Thursday for a client with a M1014 model M4. We torqued the screws to the factory spec 18 inch pounds. When we went to install the barrel, the second from the rear fastener was extending into the receiver and preventing the barrel from seating freely. We apply Loctite primer to both the threads on the receiver and the fastener. Then Loctite 243 to the fastener's threads.

 

We ended up using one of the factory washers on that fastener to allow the proper torque applied. Not a big deal really. Just an anomaly.

 

Is this something you've encountered before?

 

Sorry to hear that. Unfortunately it is. #8-40 fasteners are very rare and high quality ones are difficult to come by. We've found that 1 in several hundred are slightly longer than the rest. It's always advisable to check if any of them protrude from the inside of the receiver after installation, and prior to re-inserting the barrel.

 

If one does, a few minutes of filing the errant screw will usually remedy the situation.

 

Our instructions recommend only 16in-lbs max, but I doubt that going to 18 would be the difference here.

 

If anyone else has an issue, please feel free to contact us and we'll send you a cherry-picked shorter replacement screw.

Edited by Scalarworks

Share this post


Link to post
Share on other sites

Just received one of Scalarworks Low Drag mounts for the Aimpoint T1, absolute co-witness to replace a LaRue absolute co-witness mount without a throw lever. I compared the weight difference between the two, and the Scalarworks unit is 1.1 ounces lighter than the LaRue.

 

The mount is really nice. It has a larger mounting footprint than the LaRue does. Basically the entire base of the mount is attached to the ratcheting knob.

 

It's a nice edition to my lightweight build.

 

007_zpsi0paz6ew.jpg

 

005_zpsiqjxj0tu.jpg

Share this post


Link to post
Share on other sites

I purchased one of those to put a T2 on my H&K 93 for the purpose of seeing the stock irons through the Scalarworks mount - it works like a charm and is a wonderful mount.

Share this post


Link to post
Share on other sites

Nowhere online have I found it...but I'd love a shot of the irons zeroed looking through the BOR /RMR combo with the dot off. Pretend the rmr isn't there. I want to see where the irons fall in that window. I'm considering the dual power rmr, and when the dot washes, would simply transition to irons similar to leupold DEVO/LCO.

Share this post


Link to post
Share on other sites
Nowhere online have I found it...but I'd love a shot of the irons zeroed looking through the BOR /RMR combo with the dot off. Pretend the rmr isn't there. I want to see where the irons fall in that window. I'm considering the dual power rmr, and when the dot washes, would simply transition to irons similar to leupold DEVO/LCO.

 

We have a video of the sight picture you can expect from the BOR110 here: https://scalarworks.com/optic-mounts/bor-rmr/

Share this post


Link to post
Share on other sites

Ordered my BOR/RMR bundle yesterday , received it today ! Absolutely fantastic, well made, low profile. Thanks !!

Share this post


Link to post
Share on other sites
Ordered my BOR/RMR bundle yesterday , received it today ! Absolutely fantastic, well made, low profile. Thanks !!

 

Thanks! We're really glad you're happy with your new BOR/RMR bundle.

Share this post


Link to post
Share on other sites

Hi, all.

 

Just a quick heads up that several weeks ago we started measuring every #8-40 mounting screw that we include with the BOR/RMR to ensure that it was the correct length for M2/M3/M4 receivers.

Share this post


Link to post
Share on other sites
is this mount compatible with Remington Versa Max?

 

Not out of the box. The receiver profiles are the same, but you'd have to have your receiver drilled and tapped by a good gunsmith. Assuming there's nothing inside the receiver that might prohibit that.

Share this post


Link to post
Share on other sites
Fit and finish are excellent, and it works perfectly. Love it!

 

Thanks!

 

We're really excited to bring everyone the next evolution of our shotgun rail.

 

Stay tuned.

Share this post


Link to post
Share on other sites

Looking fwd to see what you have in store for us! This is an exciting time for the Benelli M4 community with ScalarWorks, IWC, AVA, CarrierComp, and others making high quality parts!

Share this post


Link to post
Share on other sites
When do you expect your RMR rails for the Benelli to be back in stock? I assume it's a newer design since brownells cancelled the old model?

 

I hope so. I haven't logged in for a while and see this new mount and it's out of stock/discontinued.

 

My M4 does have a picatinny rail though. Maybe I should just stick with it?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...