GTTom Posted August 30, 2020 Share Posted August 30, 2020 So just a quick question. When installing the Briley carbon fiber mag tube do you use Red Loctite on the new tube like on the original Benelli part? I'm thinking should I want to replace the carbon fiber tube in the future would heating the end of the tube damage the carbon fiber? Use Blue Loctite or none needed? Thanks in advance! Quote Link to comment Share on other sites More sharing options...
aznwhip Posted August 30, 2020 Share Posted August 30, 2020 I used blue Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted August 30, 2020 Share Posted August 30, 2020 Blue or low yield purple. Reason being you aren’t going to want to heat the carbon fiber tube to remove it down the road for whatever reason. Quote Link to comment Share on other sites More sharing options...
GTTom Posted August 30, 2020 Author Share Posted August 30, 2020 Pretty much what Was thinking. Thanks guys! Quote Link to comment Share on other sites More sharing options...
GTTom Posted August 31, 2020 Author Share Posted August 31, 2020 Received a reply to an email to tech support at Briley MFG. Of course they recommend Red Loctite. But I'm going with Blue Loctite so I can resell it if I ever change it out ? "Yes you will need to use a thread locker on the magazine. Typically we use high strength Loctite 271 which is red in color but even a a high strength thread locker found in you local hardware will work well. You will need to strip the receiver completely to apply heat to the magazine so as to release the factory thread locker. To avoid discoloration to the receiver apply the heat to the magazine as close as you can go to the receiver and allow it to transfer to the threads. You will need to carefully clamp the receiver and have something you can use to grab on the hot magazine so as to unscrew it. Clean and degrease all the threads thoroughly before applying thread locker. Hand pressure is adequate when tightening the magazine and then allow about 20 minutes for the locker to set before assembly. Full cure is 24 hours." Quote Link to comment Share on other sites More sharing options...
GTTom Posted September 19, 2020 Author Share Posted September 19, 2020 Installed the Briley CF tube with the extended follower made by Nordic. Really like looks. 1 1 Quote Link to comment Share on other sites More sharing options...
StrangerDanger Posted September 19, 2020 Share Posted September 19, 2020 Looks good! With that muzzle device, I’d probably add that Briley one round extension cap. 1 Quote Link to comment Share on other sites More sharing options...
GTTom Posted September 19, 2020 Author Share Posted September 19, 2020 Well I do have some Briley customer loyalty points stacking up...........? Quote Link to comment Share on other sites More sharing options...
Redwingsfansfc Posted September 20, 2020 Share Posted September 20, 2020 That carbon tube is starting to grow on me. Looks great! Quote Link to comment Share on other sites More sharing options...
RPC Posted September 20, 2020 Share Posted September 20, 2020 19 hours ago, Redwingsfansfc said: That carbon tube is starting to grow on me. Looks great! F, me too... Quote Link to comment Share on other sites More sharing options...
D'zaster Posted September 21, 2020 Share Posted September 21, 2020 Yeah, that turned out really nice! Quote Link to comment Share on other sites More sharing options...
GTTom Posted September 21, 2020 Author Share Posted September 21, 2020 Got some range time yesterday. Surprise..... didn't think to check capacity before going to the range but turns out I could only get 6 rounds of 2.75" Federal slugs in the magazine. Performed just fine though. I didn't have time when I got home to investigate the reason but will get some time next week. I don't think the extended follower is the problem. It slides over the spring pretty easily so shouldn't take up any more spring length. I'll probably swap the FFT follower back just to make sure. I'll have to double check the spring provided by Briley with the tube. Definitely longer then the factory spring that came with the 5 round tube but that is expected. So other than cutting a full coils off the Briley spring anything else I should look for? Quote Link to comment Share on other sites More sharing options...
aznwhip Posted September 22, 2020 Share Posted September 22, 2020 Cut the spring. Quote Link to comment Share on other sites More sharing options...
RPC Posted September 22, 2020 Share Posted September 22, 2020 4 minutes ago, aznwhip said: Cut the spring. This is the way. Quote Link to comment Share on other sites More sharing options...
GTTom Posted September 22, 2020 Author Share Posted September 22, 2020 Great! Pretty much what I thought. Thanks! Quote Link to comment Share on other sites More sharing options...
gm2376 Posted November 13, 2020 Share Posted November 13, 2020 is it necessary to use locktite at all? Would a real good hand tight lock it in? I am thinking for cleaning purposes, no locktite. Quote Link to comment Share on other sites More sharing options...
Birdog19 Posted November 17, 2020 Share Posted November 17, 2020 On 11/13/2020 at 7:32 AM, gm2376 said: Is it necessary to use loctite at all? Would a real good hand tight lock it in? I am thinking for cleaning purposes, no loctite. I'm with you. Since changing out the mag tube from OEM to Nordic Comp to FFT to Carrier Comp, I have never used loctite. Hand tight works for me, but I check it during reassembly to make sure it remains tight. Then again, I don't use the mag tube spring retaining clip either, I just let the barrel locking nut do the work of keeping the spring in the mag tube (always wear safety glasses (or close your eyes?) when dicking with that mag spring!). That makes it easier to run a dry swab-its down the mag tube on occasion to remove any dust or dirt. No lubing the in the mag tube or on the spring. Quote Link to comment Share on other sites More sharing options...
fatbiker852 Posted March 2, 2021 Share Posted March 2, 2021 On 9/21/2020 at 5:25 PM, GTTom said: Got some range time yesterday. Surprise..... didn't think to check capacity before going to the range but turns out I could only get 6 rounds of 2.75" Federal slugs in the magazine. Performed just fine though. I didn't have time when I got home to investigate the reason but will get some time next week. I don't think the extended follower is the problem. It slides over the spring pretty easily so shouldn't take up any more spring length. I'll probably swap the FFT follower back just to make sure. I'll have to double check the spring provided by Briley with the tube. Definitely longer then the factory spring that came with the 5 round tube but that is expected. So other than cutting a full coils off the Briley spring anything else I should look for? Were you able to identify why the capacity was limited? I'm considering buying the Briley CF tube for my M4. Quote Link to comment Share on other sites More sharing options...
Diesel79 Posted March 3, 2021 Share Posted March 3, 2021 Some shells are just longer than others. My carrier comp tube will hold 6rds of the federal flite control buckshot, but hold 7 federal slugs with room to spare. I’ve just been loading 2 slugs first then 5 of the buckshot and it holds 7 that way. Quote Link to comment Share on other sites More sharing options...
M2_shootr Posted March 3, 2021 Share Posted March 3, 2021 On 9/19/2020 at 3:21 PM, GTTom said: Installed the Briley CF tube with the extended follower made by Nordic. Really like looks. Holy crap.....that muzzle device looks deadly! Quote Link to comment Share on other sites More sharing options...
GTTom Posted March 6, 2021 Author Share Posted March 6, 2021 On 3/2/2021 at 9:32 PM, Diesel79 said: Some shells are just longer than others. My carrier comp tube will hold 6rds of the federal flite control buckshot, but hold 7 federal slugs with room to spare. I’ve just been loading 2 slugs first then 5 of the buckshot and it holds 7 that way. I followed some advice on the forum and shortened the mag spring. Quote Link to comment Share on other sites More sharing options...
fatbiker852 Posted March 7, 2021 Share Posted March 7, 2021 For this reason I may buy the CompCarrier spring and see how that works instead of the Briley spring. This is disappointing to hear. I figured Briley would have it dialed in by now. Quote Link to comment Share on other sites More sharing options...
Kyuss Posted March 9, 2021 Share Posted March 9, 2021 On 3/6/2021 at 8:43 AM, GTTom said: I followed some advice on the forum and shortened the mag spring. After buying the Briley carbon fiber mag tube I had this problem as well. I cut the spring a couple times, but still couldn't get it where I wanted it. I ended up buying a spring from Carriercomp and it worked perfect, no cutting. 1 Quote Link to comment Share on other sites More sharing options...
fatbiker852 Posted March 10, 2021 Share Posted March 10, 2021 ^ This is good info. Thanks Quote Link to comment Share on other sites More sharing options...
Rockinfigs Posted March 10, 2021 Share Posted March 10, 2021 I didnt use any loctite...its been on there good.. i want to be able to take it off and on easily Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.